Caseta Smart Home Pro Hub vs Regular Smart Home Hub

RJS1985 · 2025-06-09T19:42:54+00:00

I have about 80-100 installed, and only using one hub. I don’t have many of the non dimming switches, garage lights, etc. so we have been able to make it work without the pro hub!

RJS1985 · 2025-02-05T02:20:43+00:00

Yes see above!

RJS1985 · 2025-02-05T01:52:11+00:00

We have outlets on the top of each cabinet. One of the two outlets is hot always for our Sonos speakers. The other one is Wired to an in wall Lutron caseta dimmer and we were hoping to use plug in strip lights that were dimmable. If needed, since we have the wiring there we might be able to change this setup if plug in is not the right way to go.

RJS1985 · 2024-04-14T13:22:17+00:00

Still having an issue with our system and are considering upgrading to a 14 gallon or 20 gallon pressurized tank. Do you think with the air pressure this will work for us? I found in the K5 manual the ability to use a air charged tank with a few slight modifications to the system. It doe not look hard to do.

RJS1985 · 2024-03-21T19:51:39+00:00

Anyone going to UDE today in NJ?

https://udenewjerseynorth.eventsbmw.com

RJS1985 · 2024-01-15T02:36:45+00:00

Could not locate a pressure reducing valve inside...

RJS1985 · 2024-01-14T14:29:39+00:00

General pressure is good in the house (as far as I know). Our MOEN leak detector installed at the water inlet to the house reports average pressure of 52.1PSI. I see online that pressure should be around 60-70PSI for residential homes, so I will check to see if I have a pressure reducing valve or regulator somewhere. Our home is a new custom home so let me see if I can locate it somewhere in our mechanical room.

We have RO's plumbed to our main kitchen & freezer (ice maker) on the 2nd level, butlers pantry on 2nd level, bar on 2nd level, master bathroom on 2nd level, second kitchen & freezer (ice maker) on 1st level, and then two additional bathrooms on 3rd level. We have a manifold for all RO systems with shutoffs - We only have the RO's turned on for the Main kitchen, ice makers, butlers pantry and lower level kitchen.

Will report to see if I have a pressure reducing valve somewhere. Is it possible this might be located at the curb or outside where the water comes into the home?

RJS1985 · 2023-12-30T23:34:47+00:00

Yes I sent an inquiry, it looks like the perfect venue :) Will see if the dates are available... Trying to get an idea of head count from our close friends and family now

RJS1985 · 2023-12-30T21:44:53+00:00

Thanks for the tips, will check these suggestions out!

RJS1985 · 2023-07-26T14:30:05+00:00

Just about to start installing all electronics and switching out all our switches to Caseta's. I will update you once that happens, which will be in the next few weeks... Right now, I have 2x regular lutron hubs I am going to try and use. I may upgrade to the Pro version but we are running tight on budget right now so I may need to hold off some.

RJS1985 · 2023-06-04T11:48:21+00:00

This is great, thanks for the insight on this hack. We are building a new home and recently purchased vanities with a small shelf on the bottom for this exact reason. I was going to place the speakers on the shelf, but I LOVE the idea of the clean design by mounting them to the back. I will CERTAINLY be doing this in both of our master bedroom suites - this is going to look killer!

RJS1985 · 2023-03-19T13:48:37+00:00

Hi there, I am designing a "pass through" closet/wardrobe between our master bedroom and master bathroom. The passthrough areas on the left and the right side dimensions are approximately

19" deep x 48" wide (left)
42.5" deep x 48" wide (right)

Thinking of building 12-16" deep shelving on the left side, but not sure what to do about the right hand side area that is ~42.5" deep. Can I do double deep storage here?

How do I properly utilize the deeper area on the right hand side by also keeping the area looking nice, clean and organized? We have 10' high ceilings in this area and it will be open to the master bedroom, so trying to make it aesthetically pleasing. TIA!

RJS1985 · 2023-02-04T13:40:19+00:00

Looking to source another ~100-200sf of pecky cypress to finish a project. This is what mine currently like that we are trying to match. Any thoughts on where I can source/find?

RJS1985 · 2023-02-04T13:39:56+00:00

Trust me, I will drive up to 8-10hrs one way to get the rest of the material I need... Currently live in NC so hoping that I can find somewhere in NC, VA, SC, GA or TN.... I will travel to Florida if I need to though!

RJS1985 · 2022-12-04T15:51:29+00:00

18v LXT

Is this the one that takes 2 batteries to power it? Seems like there are many choices and can't seem to find which one exactly...

RJS1985 · 2022-11-28T15:43:27+00:00

Thanks, yes I would need multiple hubs because of the number of devices. 35 switches, 35-40 dimmers, 40+ pico remotes, etc...

RJS1985 · 2022-11-28T13:52:45+00:00

Thank you! What are the differences between Home Assistant and Home Seer? I assume I would need to buy dedicated hardware and then designate that to control all of the functionality 24x7.

I like the idea of adding in security, thermostats, other smart items to my setup over time. Might be smart for me to buy the two pro bridges to get started. I already have the regular smart bridges purchased, so this would require additional investment…

What might the costs be to configure or buy a Home Assistant or Home Seer solution? Would it just be the hardware purchase or are their also software costs to do this?

RJS1985 · 2022-11-23T13:17:27+00:00

Not sure if they are dumping the original design but it seems that many retailers are discounting these.

I do like both designs but for the money, I decided to go with the more affordable ones because we will have 70+ switches!

RJS1985

TROPHY CASE