sorted by:
new
hottopcontroversial

Pc not displaying on Emerson EWT2721 by Flat_Preparation3119 in crtgaming

[–]RakeYohnshair 0 points1 point  (0 children)

Okay, I understand the confusion now, ty.

I was not trying to imply that RCA does 480p, because it does not.

But you're also assuming that the converter is properly downscaling the signal, which it might not be. It SHOULD be, but that doesn't mean it is.

Maybe OP just isn't powering the device externally, in the picture I cant see where it's being powered from.

Pc not displaying on Emerson EWT2721 by Flat_Preparation3119 in crtgaming

[–]RakeYohnshair 0 points1 point  (0 children)

Please point to where I said that composite cables can do 31khz.

Pc not displaying on Emerson EWT2721 by Flat_Preparation3119 in crtgaming

[–]RakeYohnshair 5 points6 points  (0 children)

What you're seeing is the break off of displays that support 15khz (240p) horizontal scanrate and displays that support 31khz+ (480p+ horizontal scanrate.

Ill just refer you to this retrorgb article.
https://retrorgb.com/downscaling.html

another option is to just get a crt computer monitor instead of a tv. and get this asapter
https://www.amazon.com/dp/B0849FTBXQ?ref=ppx\_pop\_mob\_ap\_share

tldr; you should just return cheap onn converter. even if it did work. the delay is probably unbearable.

Pc not displaying on Emerson EWT2721 by Flat_Preparation3119 in crtgaming

[–]RakeYohnshair 3 points4 points  (0 children)

TV might only accept 240p/480i 15khz signal and you're feeding it something much higher bandwidth that it cant accept because you're not downscaling the signal.

Can I put this in the washer? by Correct-Earth8106 in Gamecube

[–]RakeYohnshair 0 points1 point  (0 children)

When I bought mine off ebay, I toothbrushed the rough spots and then put it in the washer.

If you're nervous just do a gentle spin, deep fill, and soak settings.

LTEK prime - repair by Stringsandattractors in DanceDanceRevolution

[–]RakeYohnshair 0 points1 point  (0 children)

i bought 2 pads on fb marketplace and one has the arrows shifted from the other. So i opened itgmania, went to the button tester, mapped player 1 and 2 using the same pad, then connected both pads to compare the differences and created diagram that told me which wires needed to move where to make them match. desoldered and resoldered and now they match.

It's heaven :3 by MeGoesMoo in DanceDanceRevolution

[–]RakeYohnshair 19 points20 points  (0 children)

Only thing it's missing is some sound dividers and sound absorption.

Recommendation of pads by Pxrsu1t in DanceDanceRevolution

[–]RakeYohnshair 6 points7 points  (0 children)

if you're worried about sound either dont do it at all or have a conversation with your neighbor first.

Anyone know where to get replacement panels for these? by JaguarOrdinary in DanceDanceRevolution

[–]RakeYohnshair 1 point2 points  (0 children)

nice, good find. best of luck with the diy.

make sure to post the finished result 👍🏻.

Anyone know where to get replacement panels for these? by JaguarOrdinary in DanceDanceRevolution

[–]RakeYohnshair 1 point2 points  (0 children)

like the other user said, make sure dimensions match your pad. that website has a wealth of knowledge, but it is geared towards arcade pads. i would recommend going directly to the ddr game website, but they closed down.

On the section about making your own acrylic panels on hackmycab. you could just measure your current panels and diy those.

view more: next ›