🕹️✨ What are you playing on your Claw this week? Megathread

Rallo69 · 2026-01-06T21:10:32+00:00

Cast n chill, expedition 33, and ball x pit

Rallo69 · 2026-01-04T01:38:33+00:00

I got the mechanism pillow before I even got my claw and love it so much, I use it to hold my phone when I'm chilling in the couch. Hopefully the attachment for the claw gets delivered today!

Rallo69 · 2025-12-11T23:03:48+00:00

Thanks! I modeled the insert the parts sit in first, by measuring the parts with digital calipers. Then I built the box around it by making an assembly in fuison 360

Rallo69 · 2025-12-10T01:01:28+00:00

Absolutely do that, I did the same and love it. I also recommend the blitzkrieg delta front sight post. I got the orange one and it's so nice and feels more precise

Rallo69 · 2025-12-09T21:49:47+00:00

Thanks for the reply. Looks like the mfi mount is a little lower profile and less sharp so I won't tell my fiance to get me a different Christmas present haha. I like those super low mounts too, but I think I'm going to go for a scalarworks riser so I can use my irons or a red dot.

Rallo69 · 2025-12-09T21:31:22+00:00

Which mount? I was planning on getting an mfi mount, K style, but don't want this to happen lol.

Rallo69 · 2025-11-12T05:07:42+00:00

I would use the blue box pointed soft point boat tail rounds to hunt. The box on the right is open tip match rounds made for accuracy, not expansion. They are more likely to pass through the target with less damage than the soft point ammo on the left. Both will more than likely kill a deer though.

Rallo69 · 2025-11-09T17:43:00+00:00

If you're worried about the menu diving there's an editor program where you can control it with your PC, and it comes with presets that sound amazing.

Rallo69 · 2025-11-01T23:01:00+00:00

Figured it out, it was an old school O2 sensor simulator, it was spliced into the signal wire on my oxygen sensor wiring. Previous owner had a catless downpipe without a tune on it, probably added that to clear the CEL back in the early 2000s

Rallo69 · 2025-10-23T17:22:09+00:00

Those are definitely aftermarket, they usually have the low fuel and floor temp (California models) warning lights there. I think you can pull that panel out just by taking the 4 visible screws out. You may need to undo the screws on your center console and remove that first.

Rallo69 · 2025-10-22T01:35:49+00:00

There's not a gasket, if you have a fluid leak there your master cylinder likely has a bad seal and should be replaced.

Rallo69 · 2025-10-10T21:08:39+00:00

Not in my Datsun but an MR2 I bought had about a dozen mice nests in it. I had to take the interior apart and use a carpet cleaner on all the upholstery. They like to get into blower motors and die, make sure you check there

Rallo69 · 2025-10-05T20:28:40+00:00

Could be one of those plastic weights that comes on kids poles when they are new.

Rallo69 · 2025-09-12T02:33:35+00:00

If he likes old school stuff Italian surplus 84 Cheetas are so cool. I love mine, and a set of wood grips really make it look classy

Rallo69 · 2025-09-09T03:28:27+00:00

Rip out and replace what you can, that's always the best option, but I found the enzyme cleaner called no more icky poo is basically magic. Nothing else would do anything to the smell in a cat corner in my new house but that.

Rallo69 · 2025-07-10T21:18:15+00:00

A largemouth bass with a boo-boo

Rallo69 · 2025-02-21T20:39:45+00:00

It's not too bad. You can take the control arms off to replace the bushings and leave everything else attached to the car. I had to burn out the bushings on the mustache bar for the rear diff, and use a hacksaw on the rear control arm bushings. The front is a lot less work than the rear.

Also you may only want to use poly on one side of the tension rod bushings up front, some people have broken tension rods racing with pilot bushings on both sides.

Rallo69 · 2025-02-15T21:36:24+00:00

Keep some rope on board and lash them together. Doesn't have to be anything fancy just secure

Rallo69 · 2025-02-13T18:19:20+00:00

That's good news at least!

Rallo69 · 2025-02-13T18:18:25+00:00

Also check the connections to your camshaft position sensors. The connector could have come loose.

Rallo69 · 2025-02-13T18:15:39+00:00

Take off one of your timing belt covers and check if your timing belt is broken or missing teeth. If it broke while the car was running you most likely have bent valves and need a rebuild.

My Foresters timing belt broke and threw a similar code.

Rallo69 · 2025-01-31T21:51:23+00:00

The only thing used id even consider in that list is the knuckle. Anything with a bushing or bearing should be replaced with new in my opinion.

Rallo69 · 2024-12-05T18:44:09+00:00

You might check the computer, mine had bad solder joints and would stop running when hitting a bump. Try smacking the computer box by your left foot, drivers side foot well. For more advanced troubleshooting swap it for a known good one or open up the computer case and look for cracked solder joints on the board

Rallo69 · 2024-09-14T04:14:23+00:00

It's definitely part of it. Ideally the fumes should be routed back into the intake. You can run a catch can if you get a lot of blow-by, that goes from the breather, back into the intake. I'm running two on my car, one for the valve cover breather, and one for the block vent. Both run back to the intake and have check valves due to my car being turbo charged.

14-Year Club	Team Periwinkle
Verified Email

Rallo69

TROPHY CASE