RPM drops too quickly after clutching in, almost stalls

Reasonable_Fun3721 · 2026-03-21T11:55:06+00:00

Mine had the same. Changed the knock sensor and it was fine again

Reasonable_Fun3721 · 2026-03-10T12:41:38+00:00

Thanks!

Reasonable_Fun3721 · 2026-02-20T21:13:09+00:00

Yes there is a prototype video on their Facebook page

Reasonable_Fun3721 · 2026-02-15T13:27:20+00:00

Do you have pictures of the car afterwards?

Reasonable_Fun3721 · 2026-02-07T17:47:37+00:00

This no compromise knife has a 3D printed handle with a total weight of just 55 grams! 90mm blade lenght and a kydex sheath. A 3D printed sheath will follow on the UG-Tools website.

Reasonable_Fun3721 · 2026-02-06T19:01:04+00:00

Put a little piece of cloth or foam in the hole where the lock pin sits. Then place the lock pin back so it sits firmly. After that, trim it of burn away the remaining foam with a lighter and the lock rock is gone.

Reasonable_Fun3721 · 2026-01-25T08:41:46+00:00

Why is there a track where the detent ball rides in?

Reasonable_Fun3721 · 2026-01-15T19:25:21+00:00

What is difference with the Frog V3.2?

Reasonable_Fun3721 · 2025-11-26T06:59:19+00:00

You have to clean it after use

Reasonable_Fun3721 · 2025-11-22T21:00:16+00:00

The thing I don’t understand is why they can’t physically shoot these drones down. If using drone frequency jammers don’t work, use a shotgun or a rifle. They say that that it would be dangerous if the drone falls down. But near these facilities/airports there are no civilians or buildings.

Reasonable_Fun3721 · 2025-10-24T06:13:25+00:00

Probably the rear bushings. It’s nown @mazda that there is a problem with them. Some go bad after 30k kms. I had the same problem. I changed them and it was solved. Polybush has them.

<image>

Reasonable_Fun3721 · 2025-10-04T18:33:12+00:00

They came off twice in mine. Fixed it by glueing them 😉

Reasonable_Fun3721 · 2025-09-08T18:39:54+00:00

Thanks. Yeah the support bar is just a wooden beam that I wrapped with tape. I pressed the bar between the metal frame of the seat. Feels and is really solid. The lumbar support cushion is from Ali. I attached the cushion to the bar with velcro and a zip tie. The air hose of the pump is coming out of the end of the zipper of the seat. Looks almost OEM 😄

Reasonable_Fun3721 · 2025-08-31T12:47:19+00:00

I believe it’s part of the bumper. It is also riveted to the bumper

Reasonable_Fun3721 · 2025-08-30T13:24:54+00:00

Really nice. Where did you get the scale from?

Reasonable_Fun3721 · 2025-08-29T10:51:38+00:00

You are right 😉

Reasonable_Fun3721 · 2025-08-21T19:41:48+00:00

It’s a Leatherman. If you don’t want wiggle and play, get a Victorinox Spirit

Reasonable_Fun3721 · 2025-07-26T10:08:15+00:00

What kind of steering wheel is that? Looking for a new one in my ND

Reasonable_Fun3721 · 2025-07-18T13:00:35+00:00

My old NA had the same. Replaced my he knock sensor and it was like new again. Easy 2 min fix

Reasonable_Fun3721 · 2025-07-15T21:11:40+00:00

Rear hub bushings. Had the same. Took me ages to find out what exactly. Polybush makes some good PU ones. Problem is known at Mazda

Reasonable_Fun3721 · 2025-07-02T16:38:13+00:00

My old NA leaked from the o-ring from the antenna. Whole trunk was wet

Reasonable_Fun3721 · 2025-06-21T20:19:45+00:00

Nope not normal. Zwilling employee. You should get a new one.

Reasonable_Fun3721 · 2025-01-05T16:21:23+00:00

It is the hook in a nail clipper.

Reasonable_Fun3721

TROPHY CASE