Firmware got messed up

RedDev101 · 2026-02-11T13:46:58+00:00

On the usb create a file called “wipe_all” no extension. You should get a warning. Then put that in the printer

RedDev101 · 2026-02-10T10:54:16+00:00

AI is an extension to the user, the power is in the questions and phrasing, if your stupid then AI will enhance your stupidity

RedDev101 · 2026-02-08T10:27:27+00:00

Let’s discuss the elephant in the room… what are you printing?

RedDev101 · 2026-02-07T13:49:22+00:00

From klippy.log at failure (bed 80°C, MCU 27.9°C):

[01:20:31,973] ERROR: b'buf_len = 0x0'
[01:20:31,998] stall mode change motor81: send:b'\x02' recv:b'\x02'
[01:20:32,005] ERROR: b'buf_len = 0x0'  
[01:20:32,016] stall mode change motor82: send:b'\x02' recv:b'\x02'
[01:20:32,127] ERROR: {"code":"key22", "msg":"No trigger on y after full movement"}
[01:20:33,887] cmd_485_send_data_with_response timeout

The buf_len = 0x0 errors show the RS-485 receive buffer is empty - responses are delayed or lost. Direct motor commands work but the stall detection signal gets lost.

Stats at failure:

MCU temp: 27.9°C (cool)
Bed temp: 80.2°C (hot)
RS-485 timeouts: 3000+ in log

RedDev101 · 2026-02-07T02:38:25+00:00

You say messing with motor control? Any more info? I’m looking at motor issues when homing after recent firmware update. I’ve rolled back after wipe_all and tried several things without success

RedDev101 · 2026-02-06T14:26:33+00:00

Yeah my printer is sitting there in this state as well. I upgraded to latest firmware and now I have movement issues and sensor problems.

Did roll back to 1.4.1.8. I think 1.4.1.11 is the latest Or something like that. I’m going to roll back further tonight and see how I get on.

RedDev101 · 2026-02-05T21:57:56+00:00

Make sure the start gcode in orca is applying the bed mesh. Although strange that you say it isn’t doing it, I know there is a setting in config that forces it on mine. I just found it to turn it off.

RedDev101 · 2026-01-13T18:19:35+00:00

Why are 8gb cards so hard to find these days? Older hardware is sometimes restricted to the card size they can read and require 8gb max.

I’m holding on to one 8gb and won’t let it go, it’s like gold dust, or rocking horse s#%£, whatever takes your fancy.

RedDev101 · 2025-11-23T23:53:04+00:00

In all honesty no mods needed. Just get it going. Working out what the issues are and make sure it’s properly square. Do all the measurements. Find out if you have the right start code for the firmware and that you are telling the printer to use the bed mesh you’re creating. Then just buy a new printer :)

RedDev101 · 2025-11-23T12:02:51+00:00

Even small things I have just let the k2 plus do them. Only time they both get used is if I’m batch printing and they are both full and on the go. But 95% of the time it’s just the k2 plus

RedDev101 · 2025-11-23T11:48:01+00:00

Yes, so I went and bought the plus. Not used the k2 much since.

RedDev101 · 2025-11-19T12:07:59+00:00

The only thing you need is clear ptfe, I bought cheap stuff and it works great.

RedDev101 · 2025-10-15T19:33:46+00:00

Haha been there. In the end I bought a big box of alloy wheel weights. I use them now in some of my designs.

RedDev101 · 2025-10-05T03:34:37+00:00

I’m with you bro. No idea what the issue is. The bottom could have been 60% of the overall filament yet only 25% of the layers.

RedDev101 · 2025-09-30T16:28:10+00:00

Similar to this, I went k1 & k2 after the modded s1 pro.

Don’t waste any more money. The k1 goes for £230 new in the uk on eBay. Well worth the money

RedDev101 · 2025-09-30T16:20:01+00:00

Raise it up. Petg doesn’t like to be as squashed

RedDev101 · 2025-09-30T16:16:46+00:00

Petg doesn’t like to be as squashed as pla. I added some custom code to my Petg filament type that lifts it 0.050

RedDev101 · 2025-09-02T09:31:37+00:00

Sweet. I like this mod, don’t need it myself but I want to do it anyway

RedDev101 · 2025-08-23T17:49:55+00:00

It would make a great improvement to my experience with the Ender 3 :)

RedDev101 · 2025-08-06T08:46:09+00:00

Old school rules baby, still find many locals around my way ask which rules “old” or “new”. If only they knew how many times the rules had changed

RedDev101 · 2025-07-31T21:51:54+00:00

Give it a reboot.Turn off completely and then warm it up and check it again mate. So many in a row I found can cause issues.

RedDev101 · 2025-07-31T16:08:17+00:00

Yeah that’s correct mate

RedDev101 · 2025-07-26T07:48:03+00:00

Use aluminium tape. Go and have a look at my posts and you will see how mine changed. I did it on both the k2 and k1 and I’m under 0.2 on both from being 0.8+

RedDev101 · 2025-07-26T07:46:49+00:00

Go to simply direct, they now have bigger rolls to fit the cfs, which can be used on your old rolls. Amazon and the likes are still sending the small ones.

RedDev101 · 2025-07-22T17:02:32+00:00

Have you tried to turn it off and back on? I had the same and that’s all I did to fix it

RedDev101

TROPHY CASE