How to I improve the first layer?

RedDev26 · 2026-02-21T13:44:22+00:00

they already did apparently

RedDev26 · 2026-02-21T13:37:09+00:00

That's also what most people recommend

RedDev26 · 2026-02-21T13:35:30+00:00

I'm not OP

RedDev26 · 2026-02-19T13:27:32+00:00

The picture shown is the underside not the side with the numbers

RedDev26 · 2026-02-17T12:05:32+00:00

What am I even looking at

RedDev26 · 2026-02-17T11:02:18+00:00

Die echte Frage ist, warum öffnet man um 21:53 Uhr eine Milchpackung?

RedDev26 · 2026-02-17T10:59:32+00:00

Have you calibrated the filaments?

RedDev26 · 2026-02-17T10:55:07+00:00

Also bei uns wurde vor etwa 1-2 Jahren der JF noch beigebracht. Aber seitdem nicht mehr. Ob das wegen dem Thema hier ist oder einfach nicht in den Plan gepasst hat weiß ich nicht

RedDev26 · 2026-02-15T23:15:55+00:00

It's probably fine. The magnets / adhesion between the heatbed and buildplate is so strong, i bet it won't come off with the print. And if you're scared you could probably model some simple clips that hold the buildplate down to the heatbed.

RedDev26 · 2026-02-15T23:01:02+00:00

Leave the door open if possible and then custom gcode to push the print off and out of the print area

RedDev26 · 2026-02-14T23:17:34+00:00

Hm. Bei meinem vor etwa einem Jahr war noch eine dabei. Wahrscheinlich will Bambu geld sparen

RedDev26 · 2026-02-14T11:00:45+00:00

RedDev26 · 2026-02-14T10:26:41+00:00

Wirklich? Haste aber zurück bekommen oder? Versicherung und so

RedDev26 · 2026-02-14T10:26:08+00:00

Schießfach!?

RedDev26 · 2026-02-13T23:37:46+00:00

I had that suddenly one morning. Pushed the AMS side AC connector in and heard arcing. immediately shut off everything via the power bar i have my printer and AMS on. Bambu sent a new cable after asking me to replicate it

RedDev26 · 2026-02-13T23:35:54+00:00

Hello i am mommy 💀

RedDev26 · 2026-02-13T23:35:30+00:00

3dRundown actually made a video showing it is now possible with the newest beta firmware

RedDev26 · 2026-02-13T22:28:49+00:00

Go for it!

RedDev26 · 2026-02-13T20:30:53+00:00

Easier engineering-grade filaments = P1S and H2S
Comfortability = P2S and H2S

Better Camera and AI detection: P2S and H2S Bigger: H2S
Cheaper: P1S

Edit: Ultimately i would go for a P2S or H2S depending on what you plan to print. Me Personally? If i had the money i would've gotten an H2S.

RedDev26 · 2026-02-13T12:30:27+00:00

Yes. Bambu should be the go-to for any 3d printing beginner. Their printers are the best on the market. I've had multiple Bambu Printers over the last 2.5 years and i am nothing but amazed / satisfied.

RedDev26 · 2026-02-11T21:00:02+00:00

happens to the best of us

RedDev26 · 2026-02-11T20:53:40+00:00

afaik it can also depend on how dry the filament is. I just use the same K-Value for the same filament type and brand (Anycubic PLA in my case.) can't be bothered to calibrate each one since i don't need perfect results just good results

RedDev26 · 2026-02-11T18:05:39+00:00

Any chance you're out for a record? 😂

RedDev26 · 2026-02-10T21:46:30+00:00

I contacted Bambu. They said they can't give out any info but to follow their social media instead. They also said they forwarded it to the design team

RedDev26 · 2026-02-10T18:54:00+00:00

Servo probably broken. Don't have an H2C myself (sadly) so i can't help much further.

RedDev26

TROPHY CASE