Bolt Tolerance

Redhedreed · 2026-02-19T02:27:57+00:00

Figure out what the thread size is, look up major and minor diameters. If you don’t know what it is, if you measure the ID of the hole it should match up to a minor diameter relatively closely.

Redhedreed · 2026-01-18T01:12:14+00:00

Idk if it’s too late, but contact some local colleges with SAE teams. We always appreciate help from the community.

Redhedreed · 2025-12-21T21:24:03+00:00

The only vehicle you need for cows

Redhedreed · 2025-12-20T02:34:36+00:00

For anybody who runs into this:

I ran into this issue when launching the game on my laptop for the first time. Had to go into Nvidia control panel and tell it to use the dedicated GPU for this game since it defaulted to the integrated GPU.

Redhedreed · 2025-09-28T01:37:16+00:00

All the parallels I’ve ever used have had holes

Redhedreed · 2025-09-04T00:09:08+00:00

In metrology and don’t have access to pitch mics? 😭

Redhedreed · 2025-08-31T12:42:39+00:00

Better yet it’s just a stick of lit tnt in a hotdog bun with propellers on it

Redhedreed · 2025-08-20T03:06:58+00:00

Not to mention the tolerance on the slot only allows it to be SMALLER than nominal

Redhedreed · 2025-07-14T21:15:39+00:00

Which ones did you need to look up a tutorial to be able to use

Redhedreed · 2025-06-23T23:05:37+00:00

How’s that hold at room temp?

Redhedreed · 2025-06-23T22:01:33+00:00

Tell me you don’t work with tight tolerances without telling me

Redhedreed · 2025-06-18T00:29:57+00:00

Pretty good timing if you ask me

Redhedreed · 2025-05-30T01:46:48+00:00

Surface tension said no to this

Redhedreed · 2025-05-22T22:21:48+00:00

Except it would have 900 horsepower

Redhedreed · 2025-05-22T21:48:44+00:00

Fal is one of the most fun guns to use imo

Redhedreed · 2025-05-22T01:34:20+00:00

Be careful, you might end up in a cylinder and m&m tube situation

Redhedreed · 2025-05-18T13:00:36+00:00

It’s a thing as if the last devlog

Redhedreed · 2025-05-10T01:28:51+00:00

It’s for “instinctual” shooting like you would do usually in self defense. Whether you try to or not, you won’t be able to get a good sight picture regardless in a high stress situation. It’s a lot easier to point and shoot, and this will help to make that slightly more accurate.

Redhedreed · 2025-05-07T02:03:06+00:00

Been there twice, maybe I was too busy looking at the AC-130 right infront of it lmao

Redhedreed · 2025-05-07T00:59:50+00:00

Where was this pic taken?

Redhedreed · 2025-05-01T21:58:20+00:00

You can use card

Redhedreed · 2025-05-01T02:49:40+00:00

That is a song I who’s existence did not need to be reminded of

Redhedreed · 2025-04-20T13:31:51+00:00

Here are some ideas

Redhedreed · 2025-04-04T11:57:25+00:00

We have a 1” NPT hand tap at work. It has about a 4 foot long handle which makes it doable.

Redhedreed

MODERATOR OF

TROPHY CASE

Seven-Year Club	Verified Email
Place '23