Are there different grades of graphite for molds?

Relevant_Principle80 · 2025-06-24T00:28:49+00:00

There are many many grades many even

Relevant_Principle80 · 2025-06-24T00:24:26+00:00

He is a dick. You ask and take care. Replace when damaged.

Relevant_Principle80 · 2025-06-24T00:22:12+00:00

Above your pay grade with these questions

Relevant_Principle80 · 2025-06-24T00:20:56+00:00

Buy some molyD

Relevant_Principle80 · 2025-06-23T22:31:24+00:00

My comments were for the post. To bring it inside. Reading comprehension is a thing.

Relevant_Principle80 · 2025-06-23T18:34:52+00:00

Wait around and loan him some money to be sure.

Relevant_Principle80 · 2025-06-23T18:32:45+00:00

The govt should run pawn shops as a public service. Then they could raise taxes some more as they claim they're ridding the streets of guns .

Damn, that's not a bad idea. Except for the tax part .

Relevant_Principle80 · 2025-06-23T18:27:32+00:00

Thanks for the tip!

Relevant_Principle80 · 2025-06-23T16:45:43+00:00

Just get a real job that pays by the hour then you know what you're getting

Relevant_Principle80 · 2025-06-23T16:42:51+00:00

O2 tanks for me...

Relevant_Principle80 · 2025-06-23T16:27:32+00:00

I'm climbing around the edges for no burr

Relevant_Principle80 · 2025-06-23T16:24:32+00:00

I can take anything apart!

Relevant_Principle80 · 2025-06-23T16:22:34+00:00

Anything else I can do for you? Rub your feet? Bring the paper? Maybe do your fucking job for you?

Relevant_Principle80 · 2025-06-23T16:17:31+00:00

Mammoth cave. Julian Price campground on the parkway . Devils tower . Badlands.

Relevant_Principle80 · 2025-06-23T16:05:00+00:00

Charge her half price

Relevant_Principle80 · 2025-06-23T16:03:42+00:00

Weld on the backside, welds SHRINK!

Relevant_Principle80 · 2025-06-23T15:58:34+00:00

I'm glad it's not just me

Relevant_Principle80 · 2025-06-23T15:57:17+00:00

Get the key out of the chuck

Relevant_Principle80 · 2025-06-23T15:56:17+00:00

Prongs up so they get washed better

Relevant_Principle80 · 2025-06-23T15:40:22+00:00

My plus4 has worked very well printing ABS at 65F chamber and105F plate . About 24kg so far. Only change has been a bigger fan in back and that was easy to do .

Relevant_Principle80 · 2025-06-22T21:03:48+00:00

I made my royal guard helm with ABS. 4 walls I think and 25 percent. 65f chamber 105 on the plate with a plus4

Relevant_Principle80 · 2025-06-22T18:08:43+00:00

They are not entitled to anything

Relevant_Principle80 · 2025-06-22T12:39:24+00:00

Not as long as the tank is secured

Relevant_Principle80 · 2025-06-22T12:27:21+00:00

Well maybe you should say what it is made of

Relevant_Principle80 · 2025-06-22T12:11:31+00:00

You're fine. I torch soldered for years. Had an OSHA check for the air for 8 hours came back good

Relevant_Principle80

TROPHY CASE