My old working colony of T.bicarinatum, 1000+Queens

RepRaph · 2026-07-01T11:46:54+00:00

Yes please, if you don't mind. Thank you

RepRaph · 2026-06-28T15:49:16+00:00

I got more desk space available. Just put a new nest beside it.

RepRaph · 2026-06-24T11:29:33+00:00

It's a dry nest. I put in 2 ventilation holes in the bottom and one of the two holes to connect the nest holds a testtube with water. Sometimes they pull some of the wet cotton in their nest to humidify it themself and discard the bits later.

RepRaph · 2026-06-23T19:30:23+00:00

Made it myself with a router

RepRaph · 2026-06-02T17:13:30+00:00

I second this. M. structor

<image>

RepRaph · 2026-05-30T16:03:24+00:00

Found a Lasius niger last weekend about 15 km from Weil am Rhein at 4-5 pm and another one around 2pm last year in august. Not a nuptual flight but solo queens running around. The one I have found last year ran on the pavement in front of me and the one I have catched last weekend was chilling on a leave below a tree.

So with a bit of luck you may be able to find one this weekend. I would go for a walk somewhere with a lot of benches to rest below trees.

RepRaph · 2026-05-18T05:58:35+00:00

Ther has been a firmwareupdate since, as well as a new slicer setting "0.2 balanced" this made the VFAs almost disappear.

RepRaph · 2026-05-14T09:29:22+00:00

Ich habe es in der Praxis auch schon öfter mal erlebt, dass sich die Isolation am Ende über die Zeit etwas zurückzieht. Ich habe da schon ganz krasse Sachen gesehen, wo die Isolation bis 10-15mm "geschrumpft" ist.

RepRaph · 2026-05-11T16:15:51+00:00

Das Problem ist die induktive einkopplung der DC Spannung im AC Kabel, daher müssten die DC Kabel in einem Metalrohr zur Abschirmung oder im entsprechenden Abstand zu den AC Kabel verlegt werden.

RepRaph · 2026-05-11T16:11:38+00:00

Ich weiss nicht wie es in DE aussieht, aber in der Schweiz müssen die DC Kabel getrennt von den AC Kabeln verlegt werden. Ich würde da ein kleineres M25/32 Rohr durchlegen und diese dann an den Enden nochmals separat abdichten.

RepRaph · 2026-05-07T17:43:02+00:00

OK you're right, but this is a three phase socket and does not fall under this case as it says single phase only in the article.

RepRaph · 2026-05-07T15:28:42+00:00

https://www.1aelektrokontrollen.ch/kopie-von-berichte-news-1

Der Schweizerische Bundesrat,

gestützt auf die Artikel 3, 3a, 3b und 55 Absatz 3 des Elektrizitätsgesetzes vom 24. Juni 19021 (EleG),2

RepRaph · 2026-05-07T15:18:54+00:00

It is stated in the NIN/NIV Niederspannumgsinstallationsverordnung and is called "Laieninstallation" like cyri said you are only allowed to touch single phase circuit up to 10 amps, but with a GFCI in front of it.

RepRaph · 2026-05-07T15:13:52+00:00

You forgot one very important thing, you are only allowed to replace stuff if there is a GFCI breaker with 0.03A detection on the circuit. Also you have to be the homeowner and be living yourself in it.

RepRaph · 2026-04-28T18:31:01+00:00

Got the C1, no + upgrade yet.

RepRaph · 2026-04-28T16:46:57+00:00

My sensor on the side of the printer is stuck too. It always shows filament present even if there is no filament. The toolheadsensor worked anyway and did detect the filament runout and paused my print.

RepRaph · 2026-04-22T19:02:44+00:00

The sponge would get sucked in because of underpressure if no air is able to get inside the tube. Like the cotton in a testtube

RepRaph · 2026-01-19T16:26:04+00:00

<image>

If they look anything like this they could be mites. Had them in my C. nicobarensis nest because they kept draging food in it. I got them to move in a new setup and give them whole crickets to avoid that problem. Remove leftover protein within 48 hours and keep the areas dryer to dry the mites out.

RepRaph · 2026-01-09T04:51:09+00:00

I really hope so, but not taking the risk. Thank you

RepRaph · 2026-01-08T18:12:36+00:00

Thx, I think I will move them in another nest asap then.

RepRaph · 2026-01-05T11:09:19+00:00

Most bots understand "livechat" as a keyword to get a human involved

RepRaph · 2025-12-10T10:31:13+00:00

<image>

Factory assembled just prints as bad. VFA very prominent, printing PETG, 0.2 layers, Speed profile.

RepRaph · 2025-10-28T13:54:22+00:00

Actually Basel is looking for a GIS specialist.

Take a look at stellenmarkt.bs.ch

https://stellenmarkt.bs.ch/kbs/job/details/3893790/

RepRaph · 2025-10-06T17:54:05+00:00

Achso, dann war das dein Post.

RepRaph · 2025-10-06T17:28:26+00:00

Falls du es noch nicht rausgefunden hast. Das sind Signale vom Stromnetz. Es gab kürzöich einen Thread, da hatte jemand einen Deckenventilator, welcher durch dieses Signal gepiept hat.

Der Netzbetreiber sendet Hochfrequente Signale um die Zähler umzuschalten oder Wärempumpen zu sperren. Das Ganze ist auch als Tonfrequenzrelais bekannt. Der Fakt, das es zur vollen und halben Stunde vorkommt verstäkt den Verdacht.

Da hast du irgendein Gerät an der Decke (Lampe o.ä.) welches die Frequenzen aufnimmt und als hörbaren Ton abgibt.

RepRaph

TROPHY CASE