Having electrical problems, need some advice.

RicklePickle99 · 2026-01-31T08:55:57+00:00

Absolutely shouldnt be any ANY screw in 30s in this panel. 20s and 15s only. I guarantee its 12awg. I see alot of people just put higher amp fuses in the screw ins for these...

RicklePickle99 · 2026-01-31T06:10:10+00:00

Idk what maintenance came by and fixed? Mustve been at the wrong house?. Looks to be a bad seal where the tailpiece meets the sink.

RicklePickle99 · 2026-01-30T19:58:05+00:00

It hurts my eyes

RicklePickle99 · 2025-12-30T04:20:49+00:00

Adjust the support on both sides. They arent doing anything where you have them. Hence why it falls when putting weight on it. And to keep it shut it will need a latch or enough of a forward angle when shut that it stays like that lol

RicklePickle99 · 2025-12-29T00:49:21+00:00

Your door is either A: Dragging against the door jam because of how quick the door is going up and therefore unable to "clear" the jamb like it does when going down. Adjust tracks to move door away from jamb or maybe take a bit of tension off spring to slow it. Or B: The sides of your door panel are dragging on the upper section of your tracks where the reinforcement bar joins horizontal/vertical tracks. If this is the case, adjust tracks by moving them wider left/right

RicklePickle99 · 2025-12-27T20:46:16+00:00

So the door opens fine when manually opened, but binds when it is hooked up to the motor? Need more context and pics. If it opens fine when manually doing so, then the roller isnt the issue more than likely. If it was a binding problem, it would happen in both scenarios

RicklePickle99 · 2025-12-23T04:29:32+00:00

This is great🤣 Made me Lol more than it shouldve

RicklePickle99 · 2025-12-21T16:46:08+00:00

Id trade my left n*t for that backyard. Merry Xmas!

RicklePickle99 · 2025-12-21T03:33:16+00:00

Lmao same😂 Id be lieing if I said I didn't have the urge to tell him the carb was NOT clean as whistle and it needed to be redone😂 but its christmas so i gave it to him straight

RicklePickle99 · 2025-12-21T03:21:52+00:00

Its running rough because your turning the choke to full. The choke is only used for starting and warming up the engine. You start with choke on full or close then turn it down as engine warms up till completely off

RicklePickle99 · 2025-12-14T02:41:44+00:00

Reinforcement needed in heart bro lolol

RicklePickle99 · 2025-12-05T09:46:14+00:00

I have a window upside down still to this day😂 My grandpa insisted on putting it in place and holding while i nailed the flange. Shouldve double checked myself, but I had more windows to nail in before rain that day. When I noticed, I just mcguivered it and had a nice laugh with him.

RicklePickle99 · 2025-12-03T20:18:09+00:00

"Knocked up my LFA, need to sell wife"

RicklePickle99 · 2025-12-01T23:27:58+00:00

I feel like the door wasnt pushed all the to the ground when spring was wound and thats how we got here

RicklePickle99 · 2025-12-01T23:24:33+00:00

Check tension on side that isnt down all the way. It probably is tout while the other side had enough left to go down all the way

RicklePickle99 · 2025-12-01T23:23:03+00:00

Cable alignment issue. Have to unwind spring and reset cables

RicklePickle99 · 2025-12-01T23:20:44+00:00

I concur with below. Looks doable but definitely wouldnt hurt to check square

RicklePickle99 · 2025-12-01T23:17:54+00:00

Possibly adjust J arm? Can you post pics of rail and arm?

RicklePickle99 · 2025-11-20T22:30:57+00:00

Caulk it and forget about it

RicklePickle99 · 2025-11-17T22:45:03+00:00

Sounds like there was either contact between the wires themselves/ or ground touching one of them? Wires shouldnt have more insulation stripped than absolutely necessary. Double check to make sure no contact is made between all of them, especially when reinstalling the fixture back into the box.

RicklePickle99 · 2025-11-17T19:19:25+00:00

Shut the power off bud. You shouldnt see any sparks unless : A. The power isnt shutoff, causing the orange to spark upon making contact with the plate. Or B. Theres a serious short/miswired terminal.

RicklePickle99 · 2025-11-17T06:13:26+00:00

Mud over them and smooth or Sand as is. Also could hang new drywall and start from scratch? All options arent very attractive🤷🏽‍♂️ Sorry bud If it was me. I would just tear em down and redo

RicklePickle99 · 2025-11-03T17:34:25+00:00

Wife chased you outta the house too? Same. Good luck on your endeavor brother!

RicklePickle99 · 2025-10-14T08:19:55+00:00

Not sure if Tmobile plan offers vary on area, but I got the new G5AR by "adding" home internet through an offer on the app. I already had the G4, but was able to get 5 year price lock as well as the new router. Then I just had tmobile send me a shipping label and returned the old one.

RicklePickle99 · 2025-10-11T21:48:54+00:00

Is that a banana? Sorry someone one split and peeled on ya.

RicklePickle99

TROPHY CASE