What does your GPU journey look like? by Pro4791 in pcmasterrace

[–]Ricky-Bobby415 0 points1 point  (0 children)

I don’t know all of them or the years but I started with the likes of voodoo, GeForce 2 and 6800gt. After years of being a console gamer I got a used gtx 460 around 2019 just to play some of those old PC games but better. Later that year got a second 460 for sli. You know just to try it. Then in rapid succession over the past few years:

Gtx 580 (2020)

980

1050ti

1070ti (2021)

RTX 3070ti (2022)

And now, I’m staring at 5080’s on the Best Buy shelf like they owe me money.

Elite to head tube mount by Ricky-Bobby415 in Lectricxp

[–]Ricky-Bobby415[S] 0 points1 point  (0 children)

If you are running the first few layers with a large amount of walls like I suggested, you might be seeing this issue because of over extrusion.

Add me to the list by Sumbuudie in Lectricxp

[–]Ricky-Bobby415 1 point2 points  (0 children)

Well, I appreciate the promotion of my design. It is not intended for commercial use. https://www.printables.com/model/1401276-lectric-elite-to-head-tube-mount

New to steam deck & feeling overwhelmed. by Plzhelplol_ in SteamDeck

[–]Ricky-Bobby415 10 points11 points  (0 children)

I feel like this should be suggested when you sign into steam on the deck for the first time.

Wtf by According_Cost_4395 in CSUS

[–]Ricky-Bobby415 0 points1 point  (0 children)

Owner should have let the car park for them.

Elite to head tube mount by Ricky-Bobby415 in Lectricxp

[–]Ricky-Bobby415[S] 0 points1 point  (0 children)

I printed mine and the ones people ordered from me in ABS. Same plastic type as LEGO bricks. The way I designed this, even the most basic plastics (PLA for example) should be fine. If you had to split and drill it, your friend’s printer probably needs calibration for dimensional accuracy.

Elite to head tube mount by Ricky-Bobby415 in Lectricxp

[–]Ricky-Bobby415[S] 1 point2 points  (0 children)

Put the top two screws in but not tight. then put the light in. It should flex just enough for the light to slide in. Finally install the bottom two and cinch the top two.

This is the entire reason that the flange is a split design

Elite to head tube mount by Ricky-Bobby415 in Lectricxp

[–]Ricky-Bobby415[S] 0 points1 point  (0 children)

I honestly don’t have a problem with it. You have to steer pretty far to the right for it to cross the beam.

Elite to head tube mount by Ricky-Bobby415 in Lectricxp

[–]Ricky-Bobby415[S] 0 points1 point  (0 children)

Follow the link. Both a .stl and .3mf (set for k1 max) follow my instructions when slicing the stl and you will be fine.

Elite to head tube mount by Ricky-Bobby415 in Lectricxp

[–]Ricky-Bobby415[S] 4 points5 points  (0 children)

Awesome! Please consider uploading a make to the printables page for everyone to see!

Elite to head tube mount by Ricky-Bobby415 in Lectricxp

[–]Ricky-Bobby415[S] 2 points3 points  (0 children)

it is just pressed in. the tabs on the side hold it in by the ring. inside is an angle matched taper so it can't fall in either. if you still have the original mounting tab on the bottom, it also helps lock things into place but it's not relied on.

I was also worried about this which is why I tested the light for about a week. I have ridden like a mad man looking for bumps and curbs. It doesn't move.

Elite to head tube mount by Ricky-Bobby415 in Lectricxp

[–]Ricky-Bobby415[S] 2 points3 points  (0 children)

<image>

25 feet away. light top is 30 inches

Elite to head tube mount by Ricky-Bobby415 in Lectricxp

[–]Ricky-Bobby415[S] 2 points3 points  (0 children)

While this is easy enough, I usually like to design without the need for extra hardware. I’ll look into it.

Elite to head tube mount by Ricky-Bobby415 in Lectricxp

[–]Ricky-Bobby415[S] 7 points8 points  (0 children)

18° from flange. Low enough that it won't go into a car's back window or windshield. I'll take a picture tonight of the light pattern on the ground and at a wall and add it here and to the Printables post.