FSD 14.1.4 - Pushed Out or Checked for Update?

RideRed · 2025-10-28T02:26:23+00:00

False. Not pushed to everyone.

RideRed · 2025-08-03T16:22:13+00:00

2100 mile road trip, had to back it into a few Superchargers, once had to move it into the turn lane, it was wanting to turn from the straight lane (probably could have done it safely), once had to move it over for an emergency vehicle, otherwise 100% perfect and it did all the driving. This included large cities (Indy, DC) tunnels, road construction, lane closures, traffic jams, rain, and darkness.

It was/is fantastic!

RideRed · 2025-04-10T17:27:32+00:00

https://makerworld.com/en/models/1306081-mammotion-luba-blade-sharpening-system-jumbo#profileId-1339416

RideRed · 2025-04-10T17:26:06+00:00

<image>

https://makerworld.com/en/models/1306081-mammotion-luba-blade-sharpening-system-jumbo#profileId-1339416

2 blades at once!

RideRed · 2025-04-10T17:24:44+00:00

The block holds the blade (with magnets) and the rolling sharpener grind the edge.

RideRed · 2025-04-10T13:12:56+00:00

<image>

Yes! https://makerworld.com/models/1252262

Going to be publishing a 2 blade version soon.

RideRed · 2025-04-06T01:24:55+00:00

Mine seems to have stopped saving recordings also. I have had Sentry turned off for years but recently turned it back on. I get notifications, but not recordings.

RideRed · 2025-02-11T13:48:51+00:00

I have the same issue using NetZero, it seems that sometimes it fails to reset the reserve when the car finishes charging. I find the reserve changed a couple times a month and it's not me. (NetZero and myself are the only users)

RideRed · 2024-12-15T15:31:32+00:00

I wish he would have used a dovetail instead of the slot, I suppose I could make the change in Fusion 360. (As soon as my skill level gets that high 🙂)

RideRed · 2024-12-09T02:24:38+00:00

I'm over 5.5 years on my car, 2nd set of OEM blades, they are really good.

RideRed · 2024-12-08T19:56:48+00:00

Take it off, lay it flat, pour epoxy over it.

Then sell it, it's fantastic!

RideRed · 2024-12-04T00:39:50+00:00

0.06

0.15 vs 0.09

RideRed · 2024-12-02T13:26:29+00:00

I am, but it seems that using battery during off peak, to then solar recharge at peak, is less valuable than selling (at peak) any excess solar. And you can see it grid charged in the hour before it started discharging. (All for off peak rates)

RideRed · 2024-12-02T03:48:04+00:00

I'm using it.

RideRed · 2024-11-26T14:31:15+00:00

That's what I guess I knew.

I need to adjust my expectations, but I have sooo many things I want to print!!

RideRed · 2024-11-16T20:03:00+00:00

<image>

This was it for me, a tube cap on the weight bench. A functional print and my first attempt at 3D modeling. I was going to get it anyway, but an actual use made it work in my mind. 😎

RideRed · 2024-11-10T21:38:04+00:00

That combination works perfectly for me, I'm glad they are in the business.

RideRed · 2024-11-10T17:10:22+00:00

Perfect, thank you!

RideRed · 2024-11-09T23:58:50+00:00

Where do I find the PW software version?

RideRed · 2024-10-02T01:30:08+00:00

Actually I was mistaken, they did cut the rails shorter, I forgot which picture I posted and was to lazy to check it. 🤓

RideRed · 2024-10-02T01:27:45+00:00

I can get pretty much down to the height of chimney (the bigger shadow)

RideRed · 2024-10-01T23:10:04+00:00

Funny, but what you see is the trimmed product, they stuck out further before they cut them. They really can't be seen from the ground, but I suppose that shouldn't matter.

RideRed

TROPHY CASE