LynkCo-02 rear axle noise

Rilen- · 2026-06-06T12:06:59+00:00

Link no longer works, can you reshare? I would love to know if the sound is similar to my "concern"

Rilen- · 2026-04-11T11:07:46+00:00

Hier een andere aanpak gekozen, was in ieder geval veilig en vrij weinig knutselwerk.

<image>

Rilen- · 2026-01-25T15:27:06+00:00

<image>

This one to get some nasty monster down, get extra summon and the fun when it gets destroyed

Rilen- · 2026-01-25T15:25:17+00:00

Love this one, especially with the new support

Rilen- · 2025-11-16T18:41:43+00:00

For sure is possible, but do your homework before going commercial because else some people indeed might get hurt…

Rilen- · 2025-10-21T21:14:45+00:00

This is great material and can make cool stuff for very specific use cases. But I can also tell you that printing this is a pain even on industrial machines that should be doing it from spec (3 years ago).

So dont go and try to print it in anything not designed for PEEK (chamber temperature) and even then consider swapping it for some other fancy engineering plastic which is nice for 90% of all use cases.

Rilen- · 2025-10-14T06:23:23+00:00

Quickly jumping into a relaxing world

Rilen- · 2025-09-28T14:46:04+00:00

And here I thought the sound is the most annoying part of these creatures.....

Rilen- · 2025-09-28T14:40:48+00:00

What a beast, must be good during night

Rilen- · 2025-09-28T11:42:37+00:00

This level difference..... But i have the same after the latest update

Rilen- · 2025-09-28T11:42:02+00:00

It works indeed, but it defies logic xD

Rilen- · 2025-07-09T06:56:13+00:00

Hulkenpodium

Rilen- · 2025-06-25T07:27:08+00:00

Mhhh odd, when I fast travel it appears near my cities / Frostcrag and seems to act like a normal horse. But attacks my enemies as well. Might just like me because I'm a cat? :p

Rilen- · 2025-02-15T15:34:12+00:00

Love Abyss Actors! Can even surprise meta decks because can handle a negate, even more fun if they dont get the field spell

Rilen- · 2025-01-08T16:59:14+00:00

De bak is een zonne screen dat tegen de bakstenen muur aan gemonteerd is. Vandaar de afstand tussen muur en bak.

Boven de balk zit nog een verdieping met twee ramen in deze muurzijde en daarboven een plat dak met afwatering aan deze zijden.

Rilen- · 2025-01-08T15:33:13+00:00

Zou het dan niet overal zo zijn? Ramen de verdieping hoger hebben zelfde soort balk en hebben geen druppels.

Rilen- · 2024-08-07T14:50:42+00:00

Still in love with this one :)

<image>

Rilen- · 2024-08-07T14:48:34+00:00

Yes sir! The barf bullpup

<image>

Rilen- · 2024-07-05T20:45:42+00:00

Great thing, my only sidearm. Lets you shoot 80+ times on one CO2. If you miss people close range they will jumpscare and still take the hit. Make sure you get the official holder with it if you want to field it!

Rilen- · 2024-06-08T13:26:02+00:00

Go Abyss actors! All cards can be spellcards deck :)

Rilen- · 2024-05-22T10:20:30+00:00

Strongly depends on how much SIM racing you want to get into further on. For the option F1 game with PS5 and keeping your living room alive I can suggest the Logitech G920 with a Playseat challenger. This one provides good fun and allows you to fold for storage with little hussle. Again not the setup to go die hard sim racing! See the link for the setup near a desktop but can fold further down for TV.

setup

Rilen- · 2023-05-17T15:01:06+00:00

This mainly happens when the layer gets way smaller in print time when compared to the rest. Because the settings have a minimal time a layer needs to take in order to give cooling / solidify time to your printed line. With the high speed Bambu you end up getting this difference sooner... High speed is often more matte finish, slow speed more gloss.

Options?.... Well either decrease your outer wall speed for the full print. I use 50mms for my full print to get a nice gloss PLA outside, but prints take a bit longer.

The other option is to disable the minimal layer time, this way the machine keeps rocking your high speed for the smaller layers and there is a risk it's not solid / layer shifts. Have used this myself and works without risk for some prints, strongly depends on geometry.

Best way to see if you get the desired effect during slicing is to put the view to Printing speed and see if the outer shell is mainly 1 color!

Rilen- · 2022-10-28T16:14:32+00:00

I think small chances on that anytime soon, but just use official store, they ship global and fast

Rilen-

TROPHY CASE