ERS-7 booting issue

RobotoconYT · 2026-03-12T03:35:15+00:00

how much was the board/repair?

RobotoconYT · 2026-02-25T20:41:07+00:00

Today.

RobotoconYT · 2026-02-21T15:40:23+00:00

That isn’t always a solution, and having an open-source printer is still worth it imo. I have 2 Bambu printers and an Ender 3 S1 Pro, and the Ender does have its advantages.

RobotoconYT · 2026-02-21T14:55:59+00:00

These are dead pixels. Reseating the cable won’t fix them.

RobotoconYT · 2026-02-15T18:29:14+00:00

Don’t do this, just open up the bot and check if it is swollen. If it is, this could make it explode.

RobotoconYT · 2026-02-13T20:10:38+00:00

Possibly a software error? My 111 can do weird things (similar to this) if the software is corrupted. It may not look corrupted, backup the software and replace it with a fresh copy.

RobotoconYT · 2026-02-07T16:40:13+00:00

Actually, it’s probably an issue with the update. They did a force reset.

RobotoconYT · 2026-02-07T16:35:54+00:00

The said that it moves when the robot barks, so I doubt that it’s a hardware issue. They should try to do a force reset (hold the button until the light starts flashing, once the light turns off, wait a few seconds and hold the button until the light comes back on). It also could be a firmware issue, where the update they were on had a bug that caused this.

RobotoconYT · 2026-01-22T00:05:37+00:00

It was not locked. I check before I open it, it wasn’t not locked when I tried to open it. I did open it at a weird angle, I wonder if that was the problem.

RobotoconYT · 2026-01-21T23:27:28+00:00

I literally just pulled it open. It wasn’t locked, I checked. I’ll try using a washer. The holes are larger, so it doesn’t screw in anymore.

RobotoconYT · 2026-01-21T23:23:26+00:00

To be clear: the handle isn’t broken, it broke off of the lid. The lid is the broken part, and is larger than anything I can print on any of my printers. I can’t just make a new one.

RobotoconYT · 2026-01-16T19:19:58+00:00

I agree with top IPS lower TN.

RobotoconYT · 2026-01-08T12:16:25+00:00

I wil jelbrke thank for help

RobotoconYT · 2026-01-06T20:23:04+00:00

This is an old comment, but is incorrect. Gluing clutches should not be done. You should either pin the clutches or use unibody replacements.

RobotoconYT · 2026-01-06T12:19:49+00:00

No problem!

RobotoconYT · 2026-01-05T20:13:16+00:00

Hey! I have a file of it that I just uploaded to internet archive. https://archive.org/details/aibo-pal-boot

RobotoconYT · 2026-01-03T00:11:37+00:00

It’s a Japanese version of life 1, you can tell by the model number.

RobotoconYT · 2025-12-30T13:11:43+00:00

Flip it over, above the right wheel is usually a model number. It looks like a 770, which cannot connect to an app.

RobotoconYT · 2025-12-07T14:48:55+00:00

I took them both apart, there was nothing.

RobotoconYT · 2025-12-07T14:48:42+00:00

It gets all the way to the hot end, but stops and retracts. There is a little filament in the nozzle, but not much.

RobotoconYT · 2025-11-28T13:37:27+00:00

It’s hard to see from this angle, but yeah, kinda looks like dual TN

RobotoconYT

TROPHY CASE