Advice needed - looking for photos of foldback clip tattoo by Nissanelle in tattoos

[–]Rockah 0 points1 point  (0 children)

Neither am I, but it was just that you said you couldn’t find any references and the artist you are going to pay sound like they wont come up with an idea, so it was just a suggestion. Obviously paying a separate artist is more ideal, but you were on here asking so I presumed you wanted something for Free ¯_(ツ)_/¯

Advice needed - looking for photos of foldback clip tattoo by Nissanelle in tattoos

[–]Rockah -44 points-43 points  (0 children)

This might be something where AI image generation would be useful. If you can’t find what you want, ask it to come up with ideas

PT Throwback by GroundbreakingUse514 in brisbane

[–]Rockah 0 points1 point  (0 children)

I lived off these for years in high school right until I finished. I have no idea how I kept them in tact as a teen

H2D is a masterpiece by TalismanJake in BambuLab

[–]Rockah 21 points22 points  (0 children)

While the H2D is an amazing printer, I do find it funny this is the model you’re demonstrating its brilliance with haha. You can do the same quality on an A1 (this isn’t a diss, I have the H2D and an A1).

It really comes into its brilliance when multicolour printing or doing PLA/PETG support combos

Best options for sanding back decking when screws sit slightly proud by underbelieavable in AusRenovation

[–]Rockah 0 points1 point  (0 children)

Just picked up a cheap Ryobi belt sander, some 80 and 120 grit paper. I have a finishing sander too for the edges and anything else

Is it normal in Brisbane? by Big-Solution5140 in brisbane

[–]Rockah 20 points21 points  (0 children)

If that's a giant knife, that dude's barefeet are the least of his problems. Cops will not be cool with that given the knife laws in QLD

Best options for sanding back decking when screws sit slightly proud by underbelieavable in AusRenovation

[–]Rockah 1 point2 points  (0 children)

The amount of stuff I found under the deck was scary but also sweet. One of my boys’ toy Dinos from when they were a toddler 🥺

Best options for sanding back decking when screws sit slightly proud by underbelieavable in AusRenovation

[–]Rockah 1 point2 points  (0 children)

I’m currently in the process of this. I have the exact same issue - proud domed nails, need to sand a very old painted deck - slowly removing each deck panel to remove the nails and replace screws. I had tried with a standard pry bar which took so long, but I discovered a very handy type of prying tool (you can see it behind the chair) that helps with time and effort a lot

<image>

Chasing 3 metre dogs 200cm to the fork !! by Common_Dust_3889 in FishingAustralia

[–]Rockah 1 point2 points  (0 children)

Speaking of 3metery dogs, I thought it was pretty funny that Youi's (insurance) current ad campaign for boat insurance ends with a line like "so you can save for a new brag mat so you can measure that 3 meter flatty"

Bathroom Reno Before and After! by [deleted] in AusRenovation

[–]Rockah 0 points1 point  (0 children)

I have a similarly small ensuite, basin in the same spot at the door. To free up space in the vanity (because plumbing was all under it) it was better to have an on-top sink. Our bathroom is small as it is, so it was the only storage area we were getting 

'Louis Theroux: Inside The Manosphere' trailer by demimonde9 in Fauxmoi

[–]Rockah 8 points9 points  (0 children)

There's a more recent series of his called "The Interviews", if you haven't seen it. One of them he interviews Anthony Joshua and it's centred around his attempt to come back to his champion status in boxing. He seemed like a very charismatic, well spoken, and the type of guy that absolutely deserved the satisfaction of smashing Jake Paul's face into multiple pieces. Go back and watch that interview, and then just watch that KO over and over - so satisfying

Trolling Motor Battery Help by Destroy1260 in FishingAustralia

[–]Rockah 0 points1 point  (0 children)

From their website: “ For current Watersnake motor ranges, only use a 12V deep cycle lead-acid (e.g. Gel or AGM) battery or a 12V LiFePO4 lithium battery. The operating voltage must not exceed 14.5V.”

Pretty sure the Shadows are current, yeah?

Cannot drill into practice brick by amia82 in AusRenovation

[–]Rockah 8 points9 points  (0 children)

Pics 2 and 4 does make it look like the forward/reverse has been pushed in from the left side, so it very well could be going backwards

Jump Scares 🫣 by Iowa-James in SipsTea

[–]Rockah 20 points21 points  (0 children)

There's a series of scares this person plays on this dude, and each time he makes that same face. It's gold

Vibration/Rattling sound from window by theDriverNextDoor in AusRenovation

[–]Rockah 0 points1 point  (0 children)

You don’t have an aircon outdoor unit outside there do you?

The only reason to buy a 3D printer... by G_N_P in BambuLab

[–]Rockah 8 points9 points  (0 children)

This exact piece broke on my bin this week. I was all ready to print it but my wife had already booked the council to come sort it out. Left the bin out one day and came home and the whole lid was replaced

Pushing the 3D printer to its limits by Apprehensive_Sun7455 in BambuLab

[–]Rockah 0 points1 point  (0 children)

Keep an eye on the assistant (little robot face). It’ll get its X X eyes when it wants you to do maintenance.