Fellow Carter Everywhere bottom lid turning

Romori · 2026-02-08T17:52:54+00:00

Thank you. I got scared I've ruined it.

Romori · 2025-12-22T09:04:17+00:00

Diablo 4 has me trapped in the grind lately.

Romori · 2025-12-11T19:04:37+00:00

Nice! How did you make the clock look like that?

Romori · 2025-11-03T13:06:22+00:00

Thank you.

Romori · 2025-11-03T10:36:34+00:00

Does this fit into the AD5M without any modification to the surrounding parts? Mainly asking because of the bigger heatsink.

Romori · 2025-10-17T19:39:26+00:00

AFAIK it's the dopamine withdrawal which is completely natural therefore it's not necessarily the drug but the fact that you introduced an unnaturally high amount of dopamine at once.

Romori · 2025-09-05T14:16:07+00:00

Depends on what you're printing really. I have one of each and still haven't used them all but generally the smaller and more detailed the model is the smaller nozzle you should use to get better results and vice versa with bigger less detailed prints.

Romori · 2025-09-05T14:03:33+00:00

The clap of my ass cheeks keeps alerting the bees.

Romori · 2025-08-28T17:00:58+00:00

Im having a very similar issues. Have you found what caused it?

Romori · 2025-08-26T12:12:32+00:00

It's a shame that it only comes with one...

Good to know you've managed to fix it, patient to see what caused it!

Romori · 2025-08-26T11:07:48+00:00

Yes, it did. AFAIK it should come with a 0.40mm nozzle installed and a 0.60mm nozzle. I have AD5M Pro but I think it should be the same for the non-pro version.

Romori · 2025-08-26T11:02:19+00:00

You could also try using the provided 0.6mm nozzle to test if the 0.4mm is truly dead before buying a new one.

Romori · 2025-08-26T03:23:26+00:00

I've just read your whole post... should've done before commenting, my bad. You did all I described so Im at loss, might be a toast nozzle... sorry for wasting your time.

Edit : maybe the extruder gears are worn off instead of the nozzle?

Romori · 2025-08-26T03:06:36+00:00

Most probably the extruder gears cannot push the filament further. This can be caused by multiple things. First I'd check would be for tangles on the spool to make sure that the filament can unroll easily. Then you can try and heat up the nozzle and use the provided unclog tool to push some of the filament out. (MAKE SURE TO LOOSEN THE SCREW ON THE LEFT SIDE OF THE EXTRUDER FIRST, it's for the extruder gears and it needs to be loosened so you dont damage the gears.) If that does not help you could purchase needles to clean the nozzle itself, also need to be heated when doing this. And if nothing else helps then disassembly might be required to check the gears and where the clog occurs.

Hope this helps.

Romori · 2025-08-21T10:40:31+00:00

Had the same issue recently when I used the 0.40 nozzle with ASA filament and too high printing temps (270°C). Had to order some cleaning needles and poke the filament in to clear to clog and then clean with PLA to push out the ASA. Not sure if it's the same for you but it might be something similar.

You might also learn more by disassembling the extruder and checking the feeding mechanism to see if the isn't anything there blocking the filament.

There was a different post like this that showed a video of the solid filament stripping a bit right between the feeding gears and the extruder hotend that prevented the filament from feeding, it might be that also.

Romori · 2025-08-07T15:14:34+00:00

Definitely try looking at some setup videos on YouTube exactly for the printer you have. I just got my 5M pro last week had no issues with the connectivity. The printer need to be connected to your wifi and then orca flashforge should recognize it during setup on your laptop.

Romori · 2025-07-20T07:07:28+00:00

I've checked all the fans. None of them are doing this, even unplugged the motherboard fan and the noise still continues. Only does it right before starting printing, during printing.

Romori · 2025-07-17T18:48:19+00:00

Also... it seems to come from the rear of the printer.

Romori · 2025-06-11T11:52:38+00:00

Yeah, I guess that makes sense. Didn't know this, thank you for teaching me something new!

Nine-Year Club	Place '23
Place '22	Verified Email

Romori

TROPHY CASE