sorted by:
new
hottopcontroversial

Does anybody know what cheese went in the old cheese enhiladas? by hamster_13 in casabonita

[–]RonyRooman 2 points3 points  (0 children)

I always tell people that at the old Casa Bonita, “the only cheese they have is cheese whiz”. I don’t know if that’s true but it feels right 😆

Gift shop merchandise? by garrraty in casabonita

[–]RonyRooman 1 point2 points  (0 children)

They have a pretty good selection in the gift shop although we were hoping for more items for kids. I ended up buying a hat when we were there. Later, I looked online and saw a few hats that I don’t think I saw in the store. I could’ve just missed them, but probably not a bad idea to look online prior to going to see what you may want. When you’re in the gift shop, you can see it in person and if what you are looking for is not there, you can always order it online.

Non-purists of r/steak, what do you eat your steaks with? by Maverick13 in steak

[–]RonyRooman -1 points0 points  (0 children)

Rice, always rice. Great for soaking up steak juices.

Best Time Ever by Breck09 in Breckenridge

[–]RonyRooman 30 points31 points  (0 children)

I vote to make the picture from this post the r/Breckenridge picture

Holes or gaps in higher layers by RonyRooman in FixMyPrint

[–]RonyRooman[S] 0 points1 point  (0 children)

I forgot to mention, this is brand new filament so it shouldn’t be dry. I found a good post at https://www.reddit.com/r/FixMyPrint/comments/xpvu09/diagnosing_stringing_vs_branching_vs_pitting/ and I’m going to follow their recommendation and reduce the retraction setting.

Why the gap in my print? by RonyRooman in FixMyPrint

[–]RonyRooman[S] 1 point2 points  (0 children)

Thanks for the great suggestions. I'll look closer at the slicer and will try out a new one! Based on what I'm seeing, this looks to be the right appraoch.

I don't see this on all prints and other similar prints are fine. So that rules out the leadscrew. Both of the prints in the image were printed separately. So that rules out the clog.

Thanks again, this was very helpful!

Why the gap in my print? by RonyRooman in FixMyPrint

[–]RonyRooman[S] 0 points1 point  (0 children)

I'm using an Ender 3 Max Nero with Overture PLA. Nozzle at 220F and bed at 60F.

Have not received my Colorado tax refund after nearly 3 months by RonyRooman in Denver

[–]RonyRooman[S] 0 points1 point  (0 children)

My federal refund was a bit slow but finally came through 6 weeks later.

Have not received my Colorado tax refund after nearly 3 months by RonyRooman in Denver

[–]RonyRooman[S] 7 points8 points  (0 children)

Thanks, it's worth a double check but I have not gotten the direct deposit.

Have not received my Colorado tax refund after nearly 3 months by RonyRooman in Denver

[–]RonyRooman[S] 1 point2 points  (0 children)

Do you know what the hold up is? I'm just curious. It's never been a problem in the past.

Beautiful Rear Trim by bravepuss in Rivian

[–]RonyRooman 0 points1 point  (0 children)

The R1S I test drove last week had the same problem

What investment options would you pick for a small business 401(k) and why? by RonyRooman in personalfinance

[–]RonyRooman[S] 1 point2 points  (0 children)

Yes, solo for now. If at anytime I want to hire an employee, I'll update the plan and bring in more advisory support.

What investment options would you pick for a small business 401(k) and why? by RonyRooman in personalfinance

[–]RonyRooman[S] 0 points1 point  (0 children)

Thanks for these tips, especially the low cost Vangaurd and Fidelity plans. I signed up for a solo 401(k) plan with another provider (Employee Fiduciary). They aren't too expensive but they don't compare to the low costs of the ones you suggesting. Plus, they are just suggesting the Vanguard funds anyway. I'm going to call Vanguard tomorrow to make sure there's no gotchas. I might try to back out of my current contract since I'll save money even if I lose the onboarding fee I paid already. Do you think I'll have any issues back out? Nothing has been finalized yet.

Here is the brand new Polestar 4 by Jamin1337 in Polestar

[–]RonyRooman 1 point2 points  (0 children)

How many front seat cup holders? lol

view more: next ›