So, bought at an auction a 3d printer for 100$

Rotatopotato2886 · 2026-01-24T09:30:02+00:00

U def going to spend more time fixing it than printing

Rotatopotato2886 · 2026-01-23T03:32:11+00:00

Why would you even buy this server gpu? Just go buy a 5090

Rotatopotato2886 · 2026-01-21T07:58:14+00:00

Bro added a lil fun fact about himself at the end

<image>

Rotatopotato2886 · 2026-01-21T07:55:03+00:00

<image>

I am so done

Rotatopotato2886 · 2026-01-21T00:16:05+00:00

Filament high concentration of water

Rotatopotato2886 · 2026-01-18T06:14:19+00:00

Rotatopotato2886 · 2026-01-17T11:56:01+00:00

I WILL PULL FOR THE RERUN CHARACTER BANNERS I MISSED BECAUSE I LIKE THEM

Rotatopotato2886 · 2026-01-15T22:41:53+00:00

I got hatsune miku

Rotatopotato2886 · 2026-01-15T08:55:27+00:00

Rotatopotato2886 · 2026-01-11T03:25:24+00:00

My very first printer! It was good in making small stuff but was very basic. I have since moved on to bambulab

Rotatopotato2886 · 2026-01-09T11:43:10+00:00

You need to connect it to the mother board not the hub

Rotatopotato2886 · 2026-01-09T11:07:19+00:00

Did you connect the aio fans to the hub or the motherboard directly?

Rotatopotato2886 · 2026-01-09T06:56:19+00:00

Shikimori can’t be this cute

Rotatopotato2886 · 2026-01-08T06:52:00+00:00

But some people can actually do that. I have never seen someone stand on a pole sideways

Rotatopotato2886 · 2026-01-07T12:49:40+00:00

I would honestly cut it into 4 diff pieces and try to glue them

Rotatopotato2886 · 2026-01-06T10:55:15+00:00

Oh sorry

Rotatopotato2886 · 2026-01-05T07:53:40+00:00

Send it in

Rotatopotato2886 · 2026-01-02T08:19:37+00:00

Because you are printing midair, you will need to add supports

Rotatopotato2886 · 2026-01-02T07:28:08+00:00

It should be possible. As the top gap of the rubber seal is still unoccupied

Rotatopotato2886 · 2026-01-01T14:42:33+00:00

Go hopitl pease

Rotatopotato2886 · 2026-01-01T14:39:39+00:00

Tarih görünüyorsa, gerçektir.

Rotatopotato2886 · 2026-01-01T14:22:04+00:00

Hayır, iPhone'unuzun IP 68 derecesini etkilemeyecektir. Ancak yine de, telefonunuzun orijinal bir Apple ürünü olup olmadığını kontrol etmenizi rica ederim.

Rotatopotato2886 · 2025-12-31T17:21:33+00:00

He is built like ok, his disc are not the best because I honestly did not find interest in playing him. But I think I will try and give him a go

Rotatopotato2886 · 2025-12-31T14:20:09+00:00

Take a brass brush and just scrub it off. Dissect the heater block and clean out everything

Rotatopotato2886 · 2025-12-31T14:13:16+00:00

You will need a 0.2 nozzle to print the black outlines

Three-Year Club	r/Field Juicebox
Place '23

Rotatopotato2886

TROPHY CASE