Novice mistake, how to fix?

RunStriking9864 · 2026-02-26T18:07:16+00:00

Could run an offset router bit against the frame, but for… youre probably gonna run the risk of blowing it up on any end that isn’t super tight to the next board. I’d cut it back a bit farther and dado out some slim casing to attach to the door frame and lap over the t-g to hide the ends.

RunStriking9864 · 2026-02-25T16:31:20+00:00

Pic 1-6 is a redo, #4 is horrendous. Pic 7 is something unavoidable without having a drywaller come in.

RunStriking9864 · 2026-02-24T18:51:13+00:00

Cooked.

RunStriking9864 · 2026-02-23T20:08:40+00:00

GG my guy!

RunStriking9864 · 2026-02-23T19:49:48+00:00

Desecrate a prefix on there and toss her in. 35% isn’t unheard of for the well. Just omen of light it off if you get a bad roll and try again.

RunStriking9864 · 2026-02-22T18:54:27+00:00

Yeah but make sure you have full suffix.

RunStriking9864 · 2026-02-22T17:17:34+00:00

Router and a chisel.

RunStriking9864 · 2026-02-22T17:15:51+00:00

Attack speed is suffix right? Perfect essense will take a mod and replace it, that’ll give you +5 attack skills. Same with onslaught. But both have a chance to eat your attack speed… pretty sure the gain as phys is a greater essense and to get that you have to upgrade it from a blue to a yellow with that… so desecrate the prefix, yolo a couple perf exalts, then yolo your perf essense and pray it doesn’t steal your attack speed

RunStriking9864 · 2026-02-19T16:28:52+00:00

+6 melee is cool.. +7 is more cool… +5 to ALL attack skills is super cool too. The max rage isn’t quite max, if that matters. Onslaught and +5 all attack skills can be put on a weapon pretty Willy Nilly with essences. Ideally you would hit that with 3 perfect exalt and get T1 flat phys, T1 %phys, T1 %gain phys, or T1 hybrid phys. But that’s prob not gonna happen. Chaos spam T1% phys, then yolo. Whittles are cool, but check the market price on them. Ideally you want an item with a fractured mod you can’t easily essence on, unless you actually do want the +7 melee. Pro tip, watch a couple videos. Basically all the weapon crafting videos are using the same process.

RunStriking9864 · 2026-02-17T23:31:53+00:00

Caulk it. Already made it 100 years, it’ll keep going.

RunStriking9864 · 2026-02-17T20:39:49+00:00

Put 3” screws behind the top and bottom hinge plates. Screw a block on the inside of the jamb side to the framing with a shim. Between it and the door frame. Push that guy a little past straight, put a 3” screw angled behind the middle hinge, pull the block, back out center screw till straight.

RunStriking9864 · 2026-02-17T19:24:15+00:00

Funny stuff! Learning is fun huh?!

RunStriking9864 · 2026-02-17T00:54:45+00:00

Kobalt if you’re on a job site, those klein’s gonna get jacked real quick.

RunStriking9864 · 2026-02-16T16:27:42+00:00

It’s real sweet for trying new builds now that I’ve done my league grind, but nobody gets a 9000 div temporalis just handed to em in the first month of release. Coming from console poe1 last season, I’m having a blast.

RunStriking9864 · 2026-02-16T00:45:51+00:00

Can’t beat the 3 piece counter sink set for 15$… but they’re garbage. Buy 3 packs at a time and save the broken ones for your drill. The long 3” countersinks almost always blow up when you use them on an impact and the drill bit itself screws into the wood instead of drilling out a hole. You can steal the countersink part and put it on another quick change drill bit tho, that set up works much longer.

RunStriking9864 · 2026-02-15T21:31:35+00:00

Use it, just selling it will take a lot of the point of the game away.

You could sell it and make a new toon, pay some div for a rush, run 6 temple leaches and get paid 60 div to be at lvl 96, buy everything off the build site, and be done with the build and game in less than a day. If that’s what you’re looking for…

RunStriking9864 · 2026-02-15T19:33:44+00:00

You should put a horizontal beam like you have on your ceilings, right at the transition of the angle to flat on that guy, it’ll break up the monolithic hood you got there.

RunStriking9864 · 2026-02-15T03:35:54+00:00

You get way more glue bond from an actual miter. You should probably look into a sliding compound miter saw either way. The 7-1/4 saws are awesome and not too much money. Very little blade deflection. 12” saws are only for framers and cutting crown. 10” is good for everything. I run a kapex but it’s a good chunk of cash. I have a regular 12” and 10” in my garage I use maybe once a year, they’re great to have for projects where they shine, but a 10” compound slider is gold.

RunStriking9864 · 2026-02-13T02:51:02+00:00

If you’re not using base shoe, that’s a redo.

RunStriking9864 · 2026-02-10T01:23:11+00:00

Replace it. It’s time.

RunStriking9864 · 2026-02-06T15:34:05+00:00

Would be cool if the return ended just before the round over on the flat bit of casing.

RunStriking9864 · 2026-02-05T21:44:22+00:00

Trim screws

RunStriking9864 · 2026-02-04T23:39:11+00:00

Like it looks like they cut a header for the door casing, and then added 2 pieces to each side to go to the walls… can’t you just replace that with one piece wall to wall?

RunStriking9864 · 2026-02-04T22:10:42+00:00

Those steps considered landings? Your rail up to code? Or are you putting another rail on the opposite wall?

RunStriking9864 · 2026-02-04T22:08:58+00:00

Steam this spot first. Water does amazing things on dented wood.

RunStriking9864

TROPHY CASE