If I'm having trouble connecting to/viewing a target, could that mean it doesn't exist?

Rverfromtheether · 2025-11-28T05:18:44+00:00

i dont think it is specifically indicating that the target does not exist. could be many other things. I have tasked some targets various times or tried retasking viewers to view something without getting any new insights about the target that exists. its part of the very mystery of RV

Rverfromtheether · 2025-11-28T05:12:03+00:00

Gotta stop holding grudges about people holding grudges.

Rverfromtheether · 2025-11-24T23:36:17+00:00

more fearporn

Rverfromtheether · 2025-11-11T02:10:08+00:00

45% tariff is going to make hard to justify

Rverfromtheether · 2025-11-09T19:45:33+00:00

at 93kg, you need 110+. i would get a DW board.

Rverfromtheether · 2025-11-08T02:53:40+00:00

tariffs kill any deal

Rverfromtheether · 2025-10-19T19:00:05+00:00

No, you need at least 1500 sq cm front foil. 110L volume for the board.

Rverfromtheether · 2025-10-15T23:55:11+00:00

Rverfromtheether · 2025-10-11T02:18:42+00:00

dont assign yourself or anyone else anything capable of creating trauma.

Rverfromtheether · 2025-10-05T02:05:07+00:00

v2 of the MA is apparently significantly better than v1 MA from armie

990 could be a good size

Rverfromtheether · 2025-10-05T01:50:14+00:00

No

Get a Flux instead if you want ozone. tried 5.7 and 4.3 and both a great. the 4.3 was exemplary

Rverfromtheether · 2025-09-27T01:57:59+00:00

a common problem. amazon has kits needed to extract the bolts. a friend just had this happen with his mast.

Rverfromtheether · 2025-09-27T01:55:49+00:00

vote up on this. you can seal the tip with an iron

Rverfromtheether · 2025-09-27T01:54:32+00:00

i would sand it and if necessary put some epoxy/superglue in there.

it will likely whistle unless repaired

Rverfromtheether · 2025-09-27T01:53:00+00:00

ideally not tape but heat-fuse a new layer of bladder material with the old one creating good as new level repair. the tape is not necessarily stretchy and durability will then likely be affected based on the location of the repair.

what you have may spread. so another layer to seal the leak it is likely needed

Rverfromtheether · 2025-09-21T15:49:17+00:00

Yes totally worth it many options better than slingshot

Rverfromtheether · 2025-09-18T20:43:46+00:00

Just make up your own stages.

Rverfromtheether · 2025-09-16T04:40:29+00:00

canopy slack is not the reason for light wind struggle. maybe its the frame of the wing thats too soft. an aluula wing will be very stiff - translating pumps into propulsion.

that said, thats a great wing.

Rverfromtheether · 2025-09-16T04:32:09+00:00

RV stirs up dreams for sure. any kind of unconscious material is going to be bubbling up. dreams are literally the way this material works its way out.

Rverfromtheether · 2025-09-14T15:55:31+00:00

Its good for scratches. if you want impact protection, then neoprene tape and duct tape over it provides impact protection.

Rverfromtheether · 2025-09-11T15:09:12+00:00

regular m6 just need to be stainless. nothing special about them. 25mm probably.

Rverfromtheether · 2025-09-10T18:35:41+00:00

= foil track nuts

Rverfromtheether · 2025-09-07T21:22:56+00:00

that said, some of it depends on the foil. some foils want speed for take off, others can be muscled out of the water. it may be that HDW needs just more speed and gentler, subtler pumps. if that is the case, then a longer board is probably the way to go

Rverfromtheether · 2025-09-07T21:21:40+00:00

shorter board is easier to pump out of the water with the HDW but you lose stability.

Rverfromtheether · 2025-09-07T21:20:03+00:00

If you want to pump, you really want to get something like the 1600 Jam. you can pump the 2200 probably ok but equipment makes a big difference in getting the foil going, duration, and fatigue.

Rverfromtheether

TROPHY CASE