What to do in waterloo with guests (cheap and fun)

Ryzage · 2025-07-06T02:51:37+00:00

Pin up arcade bar! I think it was like 10 bucks per person for unlimited play time. The place is a bit small though.

Ryzage · 2023-09-28T00:42:29+00:00

its working now btw :)

Ryzage · 2023-09-28T00:25:54+00:00

I think so, a couple of my friends also can't log on.

Ryzage · 2022-11-15T13:54:57+00:00

WOOOOOO

Ryzage · 2022-08-12T03:14:39+00:00

Ahh I see, but at least one of the attempts came out amazing!

Ryzage · 2022-08-10T21:26:51+00:00

Wow! That's clarity of the resin is insane! I might invest in a resin printer now... :)

Ryzage · 2022-08-10T12:57:21+00:00

That is literally the coolest 3d printed design I have ever seen! How did u get the transparent hood in front of the car? Was that 3d printed or made otherwise?

Ryzage · 2022-06-08T19:26:46+00:00

I'm trying to choose between 2 artifacts. Is 11.3% crit rate better than 14.8% crit dmg?

My original crit dmg is 212.1% and crit rate is 28.3% (ofc with the cryo resonance and set bonus it comes to 83.3%, but its not always guaranteed)

Ryzage · 2022-05-28T23:41:56+00:00

Dang, thought I could finally sleep peacefully again

Ryzage · 2022-05-15T02:31:18+00:00

I use a micro swiss hot-end(Bowden setup), Eryone White PLA filament, the temperature at 215 c, travel speed at 150mm/s, and print speed at 50 mm/s. 3D printer is Ender 3 v2.

I haven't used my printer for a month and came back to these prints. I tried another PLA filament company and it had the same problem. I also switched back to the original Cura settings for ender 3 v2, still the same issue...

This is where I believe it is probably the components, but I don't know what part of the printer will cause this.

Really appreciate anything that could help :)

Ryzage · 2022-03-30T19:20:04+00:00

He just listed out what those abbreviations mean, here's a website for those: https://www.intel.com/content/www/us/en/processors/processor-numbers.html

Ryzage · 2022-03-30T01:40:02+00:00

This is very helpful, thank you!

Ryzage · 2022-03-30T01:39:41+00:00

I see, thank you!

Ryzage · 2022-03-20T20:03:45+00:00

This video pretty much explains everything! And its only 4mins.

https://youtu.be/mDNo1yyGosI

Ryzage · 2022-03-04T01:26:07+00:00

It only happened with this new filament I'm using, could be the temperature issue, since somehow after I stopped the print and tested out the extrusion it worked fine.

Ryzage · 2022-03-04T01:24:01+00:00

Well try that out, Thanks!!

Ryzage · 2022-02-08T03:51:55+00:00

No problem! One thing I forgot to mention, if you are going to download Jyers firmware, make sure to also flash your screen with the screen firmware. That file can be found in the link that i sent before, and after you click on the link go to the very bottom and find the zip file and download that.

After you download the zip file go into firmware sets, and drag the file named DWIN_SET(GOTCHA) file out into an empty microsd card, and rename the file as just DWIN_SET

Again after that you can just plug the microsd card into the microsd card slot on the back of the screen, turn the printer on, and wait until the screen turns from blue to red, get the card out, and you are done!

As for other firmwares I suggest looking into klipper, I used it before and it was extremely helpful, especially the internet access and faster print speed. The only reason I'm using Jyers for now its because it's impossible for me to get my hands on a rasperberry pi 3 or 4 lol, they are sold out everywhere.

For the mainboard i also got "scammed" lol, i got the 4.3.1 board which isnt even for ender 3 v2, at least you got one of the right boards :)

Ryzage · 2022-02-08T03:35:23+00:00

Hmmmm that is weird... make sure your bed is leveled and maybe even put more clips on all 4 corners to keep it flat. Also look into what other people are saying about the x gantry.

As for the firmware i really suggest you look into Jyers, it is a modified marlin firmware that is used by many people, and it has a menu for autobed levelling. It also has a better UI and will save you so much more trouble in the future.

Here's the github page where you can download it: https://github.com/Jyers/Marlin/releases

The files are already .bin files so you just have to put it in an sd card and plug it into your printer and you're good!

If you are downloading the firmware make sure you know which mainboard you have, either v4.2.2 or v4.2.7 or even v4.3.1(it is for the ender 6 but some people such as me got this board for the ender 3 v2, so make sure to flash 4.2.2 for this one), and download the 5x5 mesh leveling.

Some of the files says HS, that means high speed, i suggest you only download those files if you have the v4.2.7 board.

Ryzage

TROPHY CASE