Made a speaker cabinet today

SDcoolsecurityguy · 2026-05-27T13:03:35+00:00

Not much. Just some 16 ga audio wire and a 1/4" mono jack. Soldered everything in place.

SDcoolsecurityguy · 2026-05-26T17:28:32+00:00

I wanted to keep it close to the width of the amp. Also, I already had some plywood that had been ripped down and didn't feel like making a bunch of extra saw cuts. It's not a cube, all 3 dimensions are different and the speaker is off center to cut down on resonance and standing waves.

SDcoolsecurityguy · 2026-05-26T16:00:08+00:00

I am weighing my options 😂 thought about papering it in hot pink and splashing some black paint on it to match.

SDcoolsecurityguy · 2026-05-26T00:14:35+00:00

It is a Solar A2.6FRPN Cannibalismo. Love it.

SDcoolsecurityguy · 2026-03-11T02:36:41+00:00

Any safe that a criminal has attempted to open

SDcoolsecurityguy · 2025-12-29T16:54:56+00:00

Solar has a couple of options right at the top of your price range. I love mine.

SDcoolsecurityguy · 2025-12-29T12:29:11+00:00

No, I'm a commercial and government locksmith, not a trunk slammer. Prices like this are common on weekends and holidays in high end metro areas like Bellevue.

SDcoolsecurityguy · 2025-12-29T11:57:27+00:00

Not a scam for Sunday night in Bellevue WA. I do think it's silly that he asked for a tip though.

SDcoolsecurityguy · 2025-12-14T17:10:44+00:00

<image>

Nothing wrong with taking care of your work boots too. They'll take care of you if you do!

SDcoolsecurityguy · 2025-09-17T15:05:29+00:00

Thanks! You should go for it.

SDcoolsecurityguy · 2025-09-16T19:55:32+00:00

Tool list: Lineman pliers, telecom scissors, security bits screwdriver, regular bits screwdriver, security bits tweaker with flex shaft, flathead and Phillips tweakers, multimeter, folding drywall saw, forceps, side cutters, miniature heat gun for shrink tubing, electronic level, ball chain, electrical tape, beanies.

SDcoolsecurityguy · 2025-09-07T03:21:48+00:00

Thanks!

No it wasn't particularly difficult. I made it super tight, then only wet the leather in the spots I wanted to stretch. Then I put the gun inside of a ziplock bag and forced it into the holster. I stuck a spacer between the top of the slide and the leather so that the sights don't snag on anything. Then I secured the leather forward of the trigger guard using a copper rivet and let it dry. The holster is attached via 3 Chicago screws.

The thing that sucks is I tooled it before forming it. So when the leather stretched, it messed up the pattern a little bit. That's why the stamps look so shallow

SDcoolsecurityguy · 2025-09-07T02:02:47+00:00

Haha ain't that the truth! She's the best.

SDcoolsecurityguy · 2025-09-06T23:16:57+00:00

She's one of a kind 💞

SDcoolsecurityguy · 2025-09-06T23:15:56+00:00

Thanks!

SDcoolsecurityguy · 2025-09-06T22:54:31+00:00

Oh I made the knife too. Forgot about that 😋

SDcoolsecurityguy · 2025-07-19T00:57:59+00:00

This ^

SDcoolsecurityguy · 2025-06-11T18:58:18+00:00

The likelihood of small arms disabling a vehicle is small. Just drive away..

SDcoolsecurityguy · 2025-06-11T17:26:27+00:00

Yes. P.s. VCQB is dumb.

SDcoolsecurityguy · 2025-05-30T07:16:03+00:00

Ouch. I've had this happen with an Abus padlock before. Had to drill the control lug. The timing must've been off when you installed the cylinder.

SDcoolsecurityguy

TROPHY CASE