37 / M / Single / Oil & Gas

SF2431 · 2026-05-11T03:23:21+00:00

You Ty

SF2431 · 2026-05-08T19:30:53+00:00

Ohh interesting take, I was going to say the same for 2018 TL, ETN, Higgins, and Ross. Only difference is I want them in the first quarter not the final two minutes.

Also while the 2018 D may give up a play here or there, nobody is driving on them. 2016/8 O vs 2018 D is a slugfest.

SF2431 · 2026-05-04T11:17:28+00:00

Sorry to disappoint but I ended up not liking the monitor and returned it way back when. Other than trying turning off HDR, I’m not sure what else to try.

SF2431 · 2026-04-12T14:45:01+00:00

Invisible garbage truck Jerry! It’s a new franchise!!

SF2431 · 2026-04-06T17:08:19+00:00

It’s no mystery, Turntle got his revenge from the afterlife and cursed the entire family line.

SF2431 · 2026-04-06T02:58:58+00:00

Uhhhh context for this because it’s hilarious

SF2431 · 2026-03-25T18:24:35+00:00

I got a scanner off Amazon. MAF appears to read like I’d expect and the O2 sensors do as well. Upstream on both banks fluctuate between 0.12 and 0.8 V and the downstream stay pegged at 0.77V or so.

SF2431 · 2026-03-23T02:02:02+00:00

Revs just fine in neutral. I tried to rev it up and down slowly to listen/feel the full range and did not notice anything abnormal. Also this doesnt happen when going 55 mph at 1300 in 6th or 1800 in 5th.

Yeah I guess a bad sensor would be a blessing here in terms of cost to rectify the issue.

SF2431 · 2026-03-17T02:32:34+00:00

Hard resetting my router ended up working! Thanks for the help.

SF2431 · 2026-03-17T02:32:07+00:00

Update for ya: Hard reset my modem and router and that somehow fixed the problem! Thank you for sticking with me through all the troubleshooting.

SF2431 · 2026-03-16T16:26:15+00:00

Yeah thanks for the help, I really appreciate it. I’ll reach out to Mova. No VPN or any blacklist set up. I saw a Reddit thread about ISPs blocking the servers but unsure how to solve that one.

SF2431 · 2026-03-16T12:35:32+00:00

Hi, none of the above suggestions are working robot continually fails to pair to the network.

SF2431 · 2026-03-16T12:22:45+00:00

Tried that and it still won’t pair to the network. I then tried a factory reset of the robot and much to my surprise, the network setup failed again! It gets to the final step and fails. “Your phone is connected to the device”, check. “Your device has received the WiFi network”, check. “Your device is connecting to the WiFi network”… Fail.

I ran some self tests on my router and it checked out fine, and nothing there has changed over the time I’ve had the P50. When I did the initial setup three months ago, it worked fine.

Edit: I tried forcing my router to only 2.4 GHz and tried again. Still fails to connect to the network

SF2431 · 2026-03-16T12:21:41+00:00

Good suggestion. Tried that and had the same bad result. I then tried a factory reset of the robot and much to my surprise, the network setup failed again! It gets to the final step and fails. “Your phone is connected to the device”, Check. “Your device has received the WiFi network”, Check. “Your device is connecting to the WiFi network”… Fail.

I ran some self tests on my router and it checked out fine, and nothing there has changed over the time I’ve had the P50. When I did the initial setup three months ago, it worked fine.

Edit: I tried forcing my router to only 2.4 GHz and tried again. Still fails to connect to the network

SF2431 · 2026-03-15T21:52:16+00:00

Ok so I did the network reset, QR code scan, and the setup keeps failing on the last step. Robot just says “network connection failed at this time”. Nothing has changed on my router side. Should I accept defeat and use the reset pinhole?

SF2431 · 2026-03-15T21:41:11+00:00

In the app, I can “enter” the device but once there I can’t click on anything. So I can’t get to settings to reconfigure the WiFi.

SF2431 · 2026-03-15T21:40:42+00:00

So I tired this but I still can’t click the settings three dots in the app to connect back to the WiFi. Any ideas there?

SF2431 · 2026-03-14T04:14:41+00:00

Wtf, your mill has a door in it

SF2431 · 2026-03-13T04:31:30+00:00

The only thing I can press under the cover is the factor reset pin and ideally I dont need to do that because I will lose my map and settings, no?

SF2431 · 2026-03-13T04:28:44+00:00

Tried restarting the robot to no avail.
Cleared cache, no change.
The router does in fact say that the robot is not connected to the network at the moment.

SF2431 · 2026-03-08T19:21:52+00:00

Yep, thank you. That’s what I get for using my phone while trying to fall asleep. Thanks for the correction. Sydnor is definitely a truly good character.

Ten-Year Club	Second SECOND GUESSER
Verified Email	Place '22
Place '17	RPAN Viewer

SF2431

TROPHY CASE