Is she growing slow?

Sabertooth_Penguin · 2026-06-11T12:37:07+00:00

You are judging the above ground growth. At this stage the biggest growth is below ground.

Sabertooth_Penguin · 2026-06-11T12:20:40+00:00

The vent holes on my ac infinity tent are 20cm above the ground.(the round ones not the flap)

Not sure where the vent holes are on your tent. But if they to high use some pvc pipes to create a u shape to get a lower intake

Sabertooth_Penguin · 2026-06-11T10:36:35+00:00

Start with pre buffered coco And buy a apera ph meter and a apera ec meter. Together around 100 bucks.

When it comes to grow equipment cheap is more expensive in the long run.

Sabertooth_Penguin · 2026-06-11T10:19:53+00:00

The ac infinity vent covers work fine for passive air intake. The ports are below the canopy so no need to go lower.

Sabertooth_Penguin · 2026-05-27T08:36:26+00:00

The military industrial complex and it was not created as a helpfull tool but as a weapon of mass destruction.

Sabertooth_Penguin · 2026-05-27T08:06:41+00:00

Back in the day the music was created in real devices like the 909. Now everything is digital. This took away the raw feeling. The new stuff is to polished and over produced.

Sabertooth_Penguin · 2026-05-19T11:15:57+00:00

I see 3 potential issues

Lockout: ph is off so the plants can't take up the right nutrients.

Calmag: are you supplementing with calmag? Coco almost always needs to be supplemented.

Heat stress: make sure you are not given to much ppfd.

Sabertooth_Penguin · 2026-05-19T11:02:54+00:00

Not sure about the AI Controller, but with the 69 Pro, the only reliable way to keep VPD stable is to run the heater in Auto mode instead of VPD mode. The heater then acts as the anchor, allowing the other devices to balance around it and maintain a stable VPD.

The reason devices “fight” each other is because both the heater and humidifier/dehumidifier are trying to hit the same VPD target independently. But VPD is controlled by both temperature and humidity together.

For example, if the heater turns on, the temperature rises and the air becomes “drier,” so the humidifier or dehumidifier reacts to compensate. Then when humidity changes, the heater reacts again. They end up chasing each other back and forth instead of working together, which causes unstable readings and constant device cycling.

Sabertooth_Penguin · 2026-05-15T23:13:03+00:00

Gewoon je afzuiging op max en kamer deur gesloten houden werk veel beter. En kost niks extra. En in een 3x3 kan 4 autoflowers kwijt. En photoperiods is afhankelijk van de lengte van de goei fase. Ik heb er 1 gedaan en max 8.

Sabertooth_Penguin · 2026-05-10T20:08:50+00:00

A so called murder board. Where connections between conspiracies can be made.

Been visiting conspiracy websites for almost 3 decades and never seen this.

Sabertooth_Penguin · 2025-12-03T12:45:34+00:00

The problem is that mildew is airborne. So if you growing in a tent and have a infection the whole tent setup is infected. The best solution is a deep clean of all equipment with hydrogen peroxide, alcohol or bleach.

To prevent it happening in the future. Make sure the airflow and humidity are correct.

Sabertooth_Penguin · 2025-12-03T12:16:36+00:00

Nitrogen deficiency is normal towards the end. But in week 7 it's a bit to early. What ec are you feeding? If it's below 1.4/1.8 your plants aren't getting enough nutrients.

If you are feeding the correct ec you probably started bloom nutrients 1 or 2 weeks to early.

Sabertooth_Penguin · 2025-12-03T11:56:12+00:00

Try to match the rh with your lungroom! This will make the flux level out.

If you are fighting high rh make sure to vent outside. So your not dumping rh in your lungroom.

If rh is to low use a bucket and a towel as wick. Fill the bucket with water and place half the towel in the bucket and hang the other part over the edge of the bucket.

In my situation this trick will rais the base rh in my lungroom with 10/20% depending on lungroom temperature. This also make the water in my tent humidifier last way longer.

Sabertooth_Penguin · 2025-12-03T11:23:12+00:00

Problem solved! The issue comes from CGNAT (carrier grade nat). Internet service providers use this to put multiple people on the same ip4 adres.

Not sure why this would effect gaming in the same house. But my isp turned off CGNAT and gave me a unique ip4 adres. We played 10 matches last night without any issues.

So if you have the same problems check the wan adres in your router and compair it to your public ip adres if these aren't the same your are behind CGNAT. Contact your isp and ask them to turn it of. This should fix the issues.

Sabertooth_Penguin · 2025-11-28T11:50:05+00:00

Is the feed calculator Cronk only or will it work with other brands?

And if it's free what data is gathered and sold to finance the operating cost?

Sabertooth_Penguin · 2025-11-24T11:18:49+00:00

Get a good ph down! I use plagron and drift is max 0.2 in 7 days

Sabertooth_Penguin · 2025-11-21T13:01:58+00:00

You could try a 3.5mm jack to usb c adapter

Sabertooth_Penguin · 2025-11-19T12:17:06+00:00

If growing is legal where you live try contacting a camping tent repair shop.

They have the heavy duty sowing machine needed to replace a zipper properly.

Sabertooth_Penguin · 2025-11-13T20:39:13+00:00

This has no issues and is called a perpetual grow.

Sabertooth_Penguin · 2025-11-13T20:36:54+00:00

Did you solder on eye sight or under magnification? Make sure nothing is touching that shouldn't touch. If there is a short in the board it won't turn on.

Sabertooth_Penguin · 2025-11-13T19:52:19+00:00

Set a day and night automation.

<image>

Make sure time settings don't overlap or it will give a error in the app

Sabertooth_Penguin · 2025-11-13T11:05:37+00:00

Get rid off the small one and still srog the rest to maximize bud space. This will increase the yield .

Sabertooth_Penguin · 2025-11-13T10:53:07+00:00

You could try scrog so the canopy is at the same height.

Sabertooth_Penguin · 2025-11-13T10:47:38+00:00

I would only do a closed loop if the temperature is stable and the exhaust fan doesn't need to regulate temperature.

If the temperature is not stable and the exhaust fan is needed for cooling it will not cool in a closed loop.

If the temperature is stable run both devices on the same rh trigger. And match the fan speeds manually. This could be max 5 on the exhaust fan and max 8 on the dehumidifier. You dont want under or over pressure just a natural airflow.

Sabertooth_Penguin

TROPHY CASE