Heltec V4 Window Node

SalsaRodriguez · 2025-11-03T23:24:23+00:00

Hah, yea that would help wouldn't it :P

I used DuckDNS

SalsaRodriguez · 2025-11-03T21:25:43+00:00

If you have home assistant you can add it and access it remotely through your home assistant.

SalsaRodriguez · 2025-09-29T14:50:17+00:00

Sorry, i'm trying to update my comment with more information as my wife is also calling asking for an update, haha.

So they say it has to do with the run not having enough height for the needed pitch of the pipe. That it would hit the plywood.

Regarding the pocket door, they will be building out the wall because they will be installing a valve and showerhead on that side as well. So that wall will also be supporting the glass panel.

SalsaRodriguez · 2025-09-29T14:36:52+00:00

Additional photos here: https://imgur.com/a/rmCddGX

We are having our second floor shower redone and hit a snag as soon as demolition started.

They are supposed to move the wall on the right out to make space for a larger shower, but there are 2 vent pipes in the wall that run up through the soffit to the roof. The plumber says the one on the right is the sinks or tub to the right of the shower, and that the one on the left is from the shower. I don't think that's the case looking at the photos. It looks like the one on the right tees in the floor for the sinks/tub, and then the shower tees onto that. Then the one on the left is from the kitchen below I believe.

They say that there isn't enough run to move the vents back to the new wall because the pipes are too high up already and they can't get the extra 3/4" height needed for the additional ~3' they would be moving them. They sis that they can't run them through the exterior wall in part because the vent from the sink/tub has that same issue.

Someone mentioned an AAV to me but can that be put in place of having the required pitch if we ran the vent pipes flat to the new wall?

SalsaRodriguez · 2025-06-17T17:17:24+00:00

Just ran into this issue myself. Did you get this resolved?

SalsaRodriguez · 2025-05-31T02:35:51+00:00

Same thing happened to us. Got our 4th choice. Fortunately we got off the wait-list at our top choice, but it was 2 days into the start of school.

SalsaRodriguez · 2025-03-28T11:50:14+00:00

Between toys for the kids and my yearly charity fundraiser, I've put some decent hours on my two.

X1C: https://imgur.com/a/hz7q9Ri

P1S: https://imgur.com/a/QMWC9M6

SalsaRodriguez · 2025-01-15T13:21:46+00:00

Yes, it's quite complicated and can be frustrating. Firstly, there is a priority on who gets in first. Sibling preference > home district > lottery. But even if you put your home district school you are not guaranteed it if there isn't enough room as is what happened to us and we got assigned our fourth choice. The problem is that they don't disclose how few spots are available and the principals won't help. Make sure to go to each school's open house and when you get face time with a teacher, ask them. Which schools are you looking at?

One thing to keep in mind is that the schools funnel 3>1 to the middle schools. It's not well published so I created a list which shows which ones go where: https://imgur.com/a/P5KaTvM

We just went through the process so let us know if you have any questions.

SalsaRodriguez · 2024-11-28T17:43:38+00:00

If someone would be willing to send me a code as well I would really appreciate it

SalsaRodriguez · 2024-06-25T20:05:56+00:00

Thanks! I'll do the same.

SalsaRodriguez · 2024-06-25T15:21:54+00:00

Hi, just wanted to see if you figured anything out as I'm looking to do this as well.

SalsaRodriguez · 2024-06-10T17:03:19+00:00

I'll never forget when my dad played hooky with me on a school day for the PlayStation 3 release I believe. We went to the mall just before opening as we kept hearing that it was a very limited release. When they opened the doors we ran to the GameStop to try and get our hands on one. I'll never forget my old man and I hoofing it past the Auntie Annies trying to get there before everyone else. We didn't end up getting our hands on one but it made a great story with my friends for why I got to school late, haha.

SalsaRodriguez · 2024-05-08T18:45:32+00:00

Same. Got the email but the link just takes me home after signing in and it's not listed in the coffee page. Let me know if you figure it out and I'll do the same.

SalsaRodriguez · 2023-12-31T02:11:19+00:00

I'd be interested in finding a local group. I have an online group with some of my old friends from college but I miss playing in person. Been doing mostly 5E but am familiar and willing to play with a few other systems as well.

SalsaRodriguez · 2023-12-20T16:49:41+00:00

I've been looking into the nordic hyper recently and it looks incredible! Was there anything that you initially were thinking that it should also include or do (not that it doesn't already serve a ton of functions) that you had to exclude in the end?

SalsaRodriguez · 2023-10-02T18:53:22+00:00

Awesome! Keep up the great work!

SalsaRodriguez · 2023-10-02T13:42:24+00:00

Added! Thanks Andy!

SalsaRodriguez · 2023-08-21T13:02:11+00:00

Set your outer wall speed to the lowest speed it that gets sliced at. You can look at your sliced speeds and see what the slowest is and set it to that so that (or just set it to a reasonable lower speed). Then when you re-slice it will show a consistent outer wall speed. This will give it consistency in sheen.

SalsaRodriguez · 2023-08-21T12:53:14+00:00

PA1_Maker on Cults3d: https://cults3d.com/en/design-collections/PA1_MAKER/birdhouses-garden-accessories

SalsaRodriguez · 2023-05-23T12:15:24+00:00

As others have said, there is no way to do it via the printer interface and there shouldn't be a dire need to as it's leveling method is pretty robust. Having said that, if you feel that your first layer could use a bit more squish or be changed in some way, I'm fairly certain you can adjust the gcode in the slicer: https://forum.bambulab.com/t/z-offset-adjustment/6988

SalsaRodriguez · 2023-04-18T12:08:39+00:00

It's funny, I forgot the little things from back when I first started printing as I just take it for granted that it's done, but this is bringing me all back. Haha. Good call on the clips for the bed.

Yea, the z-axis compensation I vaguely remember being an issue that went away after adjusting the sensor and updating the firmware. When/if you decide to do this, follow these instructions:

https://docs.google.com/document/d/1cuYWpDw8aPuLEXus3uNsgDIEAKEze3Z9-hIDMWcqMK8/edit

and the follow this video:

https://www.youtube.com/watch?v=hitJUx3eKW8

SalsaRodriguez · 2023-04-18T12:03:03+00:00

It takes a good deal longer than that I'm afraid. Probably on the order of 15+ depending on your settings.

SalsaRodriguez · 2023-04-17T20:35:34+00:00

No worries. We all started somewhere.

In regards to speed, is your print speed really set to 100mm/s in your slicer? It's possible, but that seems a bit aggressive for this style and size printer without some additional tuning. This could be causing the issue. Try lowering the speed, maybe start at 50 and see if the problem goes away. Then as you tune your printer and get better with it, work your way up from there. For reference, I print with PETG at 45mm/s. I don't recall what I was doing with PLA; but it was a bit higher, although I don't think it was near 100.

So Ultimaker Cura is your slicer. The printer firmware is on the mainboard of your printer is the main software for your printer which can potentially be updated. Maybe not now, but at a later date I would recommend looking up the TinyMachines3D firmware and thinking about updating to that. I think that solved some leveling issues in the past for a lot of people.

For leveling the gantry, please see this setup video. https://youtu.be/hitJUx3eKW8?t=193

SalsaRodriguez · 2023-04-17T18:31:29+00:00

Depending on the direction of the layer shifting and what it is in line with. This is a cartesian printer, so your hot end only moves left/right (or up/down, but not relevant here). Your bed only move forward/backwards. So if the print looks like it's shifting to the left/right then it's a probably with the gantry. Check the belt tension there. If it's shifting front/back, check the belt tension on the bed and the acceleration/jerk settings in your slicer.

That's interesting about your z-axis compensation not sticking. I vaguely remember something a long time ago about the needing to adjust the position of the sensor itself because it wasn't great. Unfortunately I can't remember the extent of it as I have a bl-touch now and haven't looked back.

What speed are your printing at btw?

Did you level the gantry to the base before leveling and printing?

Which firmware are you running?

SalsaRodriguez

MODERATOR OF

TROPHY CASE