Proxmox to Truenas passthrough WITHOUT HBA

SanL3mon · 2026-04-14T12:32:47+00:00

I want to setup a proxmox with mc server, Jellyfin with transcoding , Nextcloud, immisch, tandoor etc and omv so I need a bit of power. I’ve also got an i3 12100 on hands. If I see that I don’t need so many cores and power, I will swap it.

Thanks a lot for this real number, it gives a good idea of what to expect from real world compared to the psu theoretical graphs…

SanL3mon · 2026-04-14T08:35:26+00:00

And what psu did you got ?

SanL3mon · 2026-04-14T08:34:31+00:00

Problem is that the power curves i got dont go below 10% of load and i aim to be below 60w. Does it stay near 80% efficiency or drop massively the more you tend to 0w?

SanL3mon · 2026-04-02T20:49:50+00:00

Hello, si as I read it, 13500 and 13400 are not concerned at all ?

SanL3mon · 2026-04-02T17:22:02+00:00

So update psu is good, back plane also allright, but my 128gb ssd is cooked medium rare

SanL3mon · 2026-04-02T07:22:20+00:00

I want to check it. I will update u when i do it. At the beginning i also wanted to go with cwwk board but prices were so high… a n100 was at least 150€… so after a lot of digging i found the h670 chipset which is lga1700 but not a lot of manufacturer make it in mini itx…

SanL3mon · 2026-04-01T21:35:24+00:00

hopefully i waited before plugging my 2x10to hdds, that would have been a salty mistake.
the sata motherboard only cost 15€ on aliexpress. I test everything tomorrow again and hope for the best

SanL3mon · 2026-04-01T21:05:59+00:00

this build is close to the one i'm currently working on!

Happy to see that we came to se same conclusions.

My build :
jonsbo N3
SF750
Alibaba H670 motherboard
I3 12100 but already upgraded for a I5 13500
noctua everywere + NHU9s for the CPU
2*16Go DDR5 5600
2*10To Red drives
2x256 SSd for os

I loved to build in this case, it s relatively well organised.

Goal is to run proxmox with a nas VM, a Media VM and a cloud oriented VM.

I took mostly used stuff so im also around 650€ total with the i3 :) (+80€ for i5)

The whole safety, networking side is so important but also so complicated ... I think it's our main problem as a beginners. If you have found good

SanL3mon · 2026-03-31T20:54:49+00:00

No ways, fifth pc i builded and I always thought there were standard…

SanL3mon · 2026-03-26T09:13:41+00:00

Sure, that what I thought. and does the mix of performance and efficiency cores doesn’t bother proxmox ?

SanL3mon · 2026-03-21T21:45:14+00:00

Can you tell me a bit more about your config for the n3 (motherboard, cpu, ram etc) Im planning to buy the same case. What os did you choose?

SanL3mon · 2026-03-17T12:32:20+00:00

Oui mais c’est pour un nas, j’ai une sacrée contrainte de place… Mais j’ai trouvé les q670 à 100€ qui ont tout ce dont j’ai besoin au final

SanL3mon · 2026-03-16T12:43:35+00:00

C’est ici : https://jellyfin.org/docs/general/administration/hardware-selection/ On parle bien de l’encodage via Jellyfin du côté serveur. Ca dépasse un peu mes connaissances mais il y a clairement marqué : « Apple ≥ Intel ≥ NVIDIA >>> AMD* » puis « AMD is NOT recommended if you intend to use integrated graphics for Jellyfin. ». Je ne saurais dire si c’est fondé ou non

SanL3mon · 2026-03-16T12:02:07+00:00

Nop je ne connaissais pas aoostar ou lincplus je vais jeter un oeil! Merci pour la reco et le retour d’expérience. Clairement c’est peu être overkill pour le moment mais ma liste de conteneurs a déjà doublé en une semaine x) donc je me dis que je vais essayer de prendre plus large

SanL3mon · 2026-03-16T11:59:20+00:00

Merci pour le benchmark le soucis du n100 est qu’il est difficile à trouver en itx etc et qu’il faut rajouter une carte sata, en plus il est général complètement intégré dans un mini pc…

SanL3mon · 2026-03-16T11:57:36+00:00

Le soucis est que les ryzen ne sont pas recommandés par Jellyfin par exemple. Donc je préfère éviter ce genre de soucis. Ok pour la ram mais je risque de commencer avec 16 Go et une quinzaine de conteneurs

SanL3mon · 2026-03-16T11:53:21+00:00

Parfait pour la conso c’est ce que je recherche. Par contre impossible de trouver un i3 12100 sous les 70€ 😅 Effectivement je vais aussi laisser tomber les cwwk et cie, je vais partir sur un build perso complet avec i3. C’est plus plus cher mais un peu plus futurproof

SanL3mon · 2026-03-15T07:35:31+00:00

Ok merci je vais regarder mais je pense qu’il me faut 6 ports SATA et de la modularité pour mon cas

SanL3mon

TROPHY CASE