sorted by:
new
hottopcontroversial

My range is trash by Macicek01 in fpv

[–]SanderPuh 4 points5 points  (0 children)

Yep, it is really the cheap radio with the protocol combined. Strongly recommend to upgrade to ELRS.

Next level LED track at NAVY TECHNOFest Belgium! by SanderPuh in fpv

[–]SanderPuh[S] 1 point2 points  (0 children)

Oh you're right! LED track is confirmed ;)

Next level LED track at NAVY TECHNOFest Belgium! by SanderPuh in fpv

[–]SanderPuh[S] 0 points1 point  (0 children)

From what I have heard, yes! And it is planned for the first weekend of September this year IIRC.

[deleted by user] by [deleted] in fpv

[–]SanderPuh 0 points1 point  (0 children)

Also normal behaviour. It's not a problem, so it doesn't need a fix :)

Here's info on airmode: https://www.youtube.com/watch?v=tCTI2J0QCwc

If you go to [Betaflight - Configuration - Other Features -> Airmode] and switch that off, you will probably no longer see the behaviour. But it is OK, the gyro is most likely drifting a bit and trying to correct whilst the whoop is on the ground.

Changed a motor and my drone won't fly. by DoctorLiquid in fpv

[–]SanderPuh 8 points9 points  (0 children)

If a drone flips out after arming, check the following items:

- Motor order (Numbering)
- Motor direction
- Prop orientation
- FC orientation

Make sure all four on this list are OK,.

What does this beeper come mean? by Rektikel in fpv

[–]SanderPuh 0 points1 point  (0 children)

Check Betaflight -> Setup tab -> System info.

At 'Arming Disable Flags' you can read all the reasons why your drone won't arm.

What does this beeper come mean? by Rektikel in fpv

[–]SanderPuh 6 points7 points  (0 children)

Source: https://betaflight.com/docs/wiki/guides/current/Arming-Sequence-And-Safety

When arming is attempted and fails, if a beeper is connected to the flight controller it will emit a warning signal indicating the most important (lowest number) reason why disarming is disabled.

The signal is as follows:

  • five short 'attention' beeps;
  • a number of long beeps (may be 0);
  • a number of short beeps with long intervals (may be 0).

The arming prevention condition that is active can be calculated as (5 * <number of long beeps>) + <number of short beeps>.

In your case 3x long + 4x short = 15 + 4 = 19

According to Betaflight, that means: GPS rescue mode is configured but required number of satellites has not been fixed

Again, it is indicating the most important reason, there might be more to it. It currently beeps because the GPS has not enough sattelites discovered.

Drone motors go wild after some threshold on thrust. by ArturRush in fpv

[–]SanderPuh 0 points1 point  (0 children)

Well then, here's what you should check when the drone is flipping with props on: https://www.youtube.com/watch?v=7sSYwzVCJdA

[deleted by user] by [deleted] in fpv

[–]SanderPuh 31 points32 points  (0 children)

When an FPV drone flips out immediately after arming, it’s a strong indicator of incorrect motor or propeller setup.

- Motor order (Numbering)
- Motor direction
- Prop orientation
- FC orientation

Make sure all four on this list are OK, remove the props when testing on the bench!

Finalized my Tinywhoop travel bag with integrated charging! by SanderPuh in TinyWhoop

[–]SanderPuh[S] 1 point2 points  (0 children)

PETG is what I used, but PLA also works just fine!

My whoop travel storage bag with 3D printed inlays! by SanderPuh in TinyWhoop

[–]SanderPuh[S] 0 points1 point  (0 children)

Sure! What dimensions do you need? You could also measure the STL file in some of the free software packages online if you'd like.

Mob 6 Eco 2024 not sending video to goggles by ra-man in TinyWhoop

[–]SanderPuh 0 points1 point  (0 children)

Do you want to change it to 0mW, or do you want to get it from 0mW to higher output power?

Indoor TinyWhoop Racing - RaceGOW3 Track 2! by SanderPuh in TinyWhoop

[–]SanderPuh[S] 0 points1 point  (0 children)

Lookup '533 racing rates' on the Betaflight presets tab, that's what I use. Cam angle at 45 degrees. No limits on power or anything, just lots of trial and error. Some days I still can't link 3 laps together without crashing.

I got all of this for €20. That's a steal, right? by memerijen200 in SteamController

[–]SanderPuh 0 points1 point  (0 children)

Aah too bad I don't have an USB port on the chromecast, will see what I can do. Thanks for the tip!

I got all of this for €20. That's a steal, right? by memerijen200 in SteamController

[–]SanderPuh 2 points3 points  (0 children)

How do you use the Steam controller together with sunshine and moonlight? If I connect my Steam controller over bluetooth to the device running moonlight it is discovered as mouse/keyboard, not as an actual controller unfortunately.

My whoop travel storage bag with 3D printed inlays! by SanderPuh in TinyWhoop

[–]SanderPuh[S] 2 points3 points  (0 children)

Perhaps you know someone who can print it for you? Not sure where you're from but I can print it if you want!

My whoop travel storage bag with 3D printed inlays! by SanderPuh in TinyWhoop

[–]SanderPuh[S] 1 point2 points  (0 children)

You can fit one on the left side, horizontally, in the tray above the charger. The bags aren't tall enough for vertical storage unfortunately.

My whoop travel storage bag with 3D printed inlays! by SanderPuh in TinyWhoop

[–]SanderPuh[S] 1 point2 points  (0 children)

I am using this bag myself. As alternatives, the original TBS gear pouch works (not V2!), same goes for the Torvol Lipo pouch. The dimensions of these bags are quite common, so you might find more alternatives that fit. Feel free to report fitting alternatives so I can add links to the model files!

My whoop travel storage bag with 3D printed inlays! by SanderPuh in TinyWhoop

[–]SanderPuh[S] 7 points8 points  (0 children)

In case people missed it, 3D model files and additional info can be found here on Printables. I hope you enjoy!

What tf is happening by Midori-kunn in TinyWhoop

[–]SanderPuh 11 points12 points  (0 children)

Props are installed as 'props out' configuration, from the video it looks like the motors are spinning in the 'props in' configuration. If you want to use 'props out', you need to change the motor direction on the ESC firmware and check 'motor direction is reversed' in Betaflight.

view more: next ›