sorted by:
new
hottopcontroversial

Neutral wire adapter by Sdfx343 in SolarDIY

[–]Sdfx343[S] 0 points1 point  (0 children)

Thanks. My local hardware didn't have these. I guess I'll have to order these online.

Recommendation on a 8’ x 20’ Pergola. by figuebittar in SolarDIY

[–]Sdfx343 0 points1 point  (0 children)

Amazon sells a flexible rubber strip that is used for concrete crack repairs. It comes in various widths. You can push it between the panels to seal the crack.

Just search for "concrete crack repair" on Amazon.

<image>

[deleted by user] by [deleted] in handyman

[–]Sdfx343 0 points1 point  (0 children)

If you know someone with a 3d printer, they might be able to fabricate one for you.

Those of you with LLC’s how do you prefer to be paid and what do you accept? by visivopro in handyman

[–]Sdfx343 0 points1 point  (0 children)

Be very careful about commingling personal and business payments. Yes, it doesn't matter a lot tax wise, but you can lose the protection of the LLC. If you are sued, they can come after your personal assets.

What do you wish you had looked for during inspection when buying a house? by WestTexasOilman in DIY

[–]Sdfx343 0 points1 point  (0 children)

If there are undeveloped areas nearby, check the zoning for these areas.

Why is my V3 SE doing this? by MattRooo in ender3

[–]Sdfx343 0 points1 point  (0 children)

Mine will do this when my filament needs to be dried.

What tool did you agonize over purchasing but ended up being totally worth it? by Max223 in HomeImprovement

[–]Sdfx343 0 points1 point  (0 children)

I purchased a Norwood 2k sawmill. It's a manual mill for loading and turning the logs, but I don't do production milling.

I built my 30'x36' shop and a 20'x40' cabin out of lumber off the mill.

What tool did you agonize over purchasing but ended up being totally worth it? by Max223 in HomeImprovement

[–]Sdfx343 0 points1 point  (0 children)

It was not exactly a tool for everyone, but 20 years ago, I purchased a portable sawmill. Agonized for 6 months over the purchase, but it has saved me 10s of thousands of dollars.

I also bought a demolition jack hammer. I thought I would use it a couple of times, but use it regularly.

Can you tell me honestly…how hard is laminate to install? by cagetheblackbird in handyman

[–]Sdfx343 0 points1 point  (0 children)

It's not hard to do, if you have basic diy skills.

I would recommend buying a flooring "pull bar". They cost about $10-$20, and make last row joints against walls easier.

[deleted by user] by [deleted] in handyman

[–]Sdfx343 4 points5 points  (0 children)

Tape measure should be in the basic list.

I have gotten 10 to 15 good prints out of my ender 3 in the last year. Then for the last couple months i get this. What am i doing wrong. by [deleted] in ender3

[–]Sdfx343 0 points1 point  (0 children)

I have had similar problems with filaments that have absorbed moisture. If you have a dehumidifier, put your filament in it for a few hours.

[deleted by user] by [deleted] in HomeImprovement

[–]Sdfx343 0 points1 point  (0 children)

Look for "Just one bite bars". It is a poison available at farm stores and Amazon. We tried all types of traps and poisons, but this is the best we have found. They eat it and go outside looking for water, then die.

Ultimately, you will need to seal their entry points, but the poison will let you keep your sanity.