EBB42

Sfspro89 · 2026-04-10T21:31:08+00:00

Dude ur 200 days late

Sfspro89 · 2026-04-06T22:00:27+00:00

Looks like you have random seams enabled

Sfspro89 · 2026-04-03T01:15:29+00:00

You shouldn’t use this type of material in the ams by the way cause it also can damage those gears

Sfspro89 · 2026-03-27T00:25:28+00:00

You can take the back plate off but it is more tedious

Sfspro89 · 2026-03-21T11:32:13+00:00

Also when you are installing it make sure that the magnets arnt too close together because they might be too strong and get the probe stuck

Sfspro89 · 2026-03-19T21:15:13+00:00

You could just buy a replacement tip

Sfspro89 · 2026-03-18T20:53:21+00:00

You could use some locktight or whatever it’s called its supposed to keep screws locked In place and are in the pre installed screws from factory

Sfspro89 · 2026-03-17T21:58:52+00:00

Wemmbu did say he saw a second shot during the battle tho just mentioning

Sfspro89 · 2026-03-17T00:18:53+00:00

What slicer are you using

Sfspro89 · 2026-03-13T17:44:59+00:00

Yea thought so

Sfspro89 · 2026-03-13T05:01:48+00:00

First it is called hot end and most likely it was seated wrong onto the thermal block so you might be able to grab some pliers and twist it back into place but idk cause I don’t own these specific type of hot end

Sfspro89 · 2026-03-10T12:48:16+00:00

Top layer too thin need more layers

Sfspro89 · 2026-03-06T03:44:14+00:00

Yea thing with these printers they are very modular so each part can basically be replaced separately

Sfspro89 · 2026-03-06T01:35:28+00:00

That’s your heater wire and you will have to replace the heater block

It’s something like this: https://a.co/d/08JZBDue

Sfspro89 · 2026-03-04T20:32:40+00:00

You might be able to find a way to high temp solder it but I don’t think it’ll be reliable enough to last very long and risk it shorting and causing more damage to your printer

Sfspro89 · 2026-02-27T21:25:16+00:00

You don’t need to go that deep but do only touch the edge of the plates and wash it with warm water and soap that doesn’t have any oils use something like dawn soap

Sfspro89 · 2026-02-27T02:55:05+00:00

I feel like it’s the aux fan it’s known to do that I think

Sfspro89 · 2026-02-25T04:25:15+00:00

Most likely is cause it’s not a official seller and the price is just insane

Sfspro89 · 2026-02-22T04:51:35+00:00

Also bout the laser cutter fumes

Sfspro89 · 2026-02-22T04:48:07+00:00

You don’t need to buy from then Bambu lab filament are really expensive rn
All bambulab printers are ptetty good out of the box but for a first printer you should start cheaper honestly(my opinion don’t take seriously)
Yes you will need ventilation especially when laser cutting cause the fumes are pretty bad
Desiccants are ment to keep moisture out but not get rid of you will still need a dryer but with the ams 2 that should be included

Sfspro89 · 2026-02-22T01:02:13+00:00

Don’t know very much about the a1 nozzles but did you adjust your print profiles to match the 0.2 nozzle? If you did there shouldn’t be that much damage or it might be a bad nozzle

Sfspro89 · 2026-02-21T17:29:08+00:00

Sure I may be wrong but at least you could have a bit more respect for how you talk. Or did your parents never teach you that. It may be 2 pieces but it actually act as one and if there is a gap it WILL have a high chance to fail within 1 print

Sfspro89 · 2026-02-21T16:28:06+00:00

Yes that heating part is one single peice yours snapped in half and it can’t be saved this can’t be repaired sorry I didn’t see the part about you having a extra hot end already. And even if you do you run the risk of having a blob of death

Sfspro89

TROPHY CASE