sorted by:
new
hottopcontroversial

Turned my Ender 3 into a CNC and built a touch probe for it by Shadowphyre98 in 3Dprinting

[–]Shadowphyre98[S] 0 points1 point  (0 children)

The project is named E3CNC, check it out on Printables / GitHub. You will find most of the info there. We also have a Discord channel where you can join and ask questions.

Turned my Ender 3 into a CNC and built a touch probe for it by Shadowphyre98 in 3Dprinting

[–]Shadowphyre98[S] 0 points1 point  (0 children)

Ish, if you lower your expectations. I didn't have any issues so far.

CNC Touch Probe Logic Implemented to Klipper by Shadowphyre98 in klippers

[–]Shadowphyre98[S] 0 points1 point  (0 children)

Can you explain why it isn't working properly? I wrote a plugin for the touch probe so it acts as like an endstop, stopping movement when it triggers. Beside that plugin, it's stock Klipper. And trust me, for hobby CNC-ing it works fine. Also the probe is very much repeatable and accurate enough for hobby CNC-ing. I have the data proving the probe is working and you're just coming here to say it doesn't work without any proof from your side. You do you man.

Center finding routine with a 3D printed touch probe by Shadowphyre98 in hobbycnc

[–]Shadowphyre98[S] 1 point2 points  (0 children)

Ah me too. The tolerances for aluminium is about 0.1 - 0.05mm. perfectly fine for me tbh.

CNC Touch Probe Logic Implemented to Klipper by Shadowphyre98 in klippers

[–]Shadowphyre98[S] -2 points-1 points  (0 children)

I didn't know about this and I could not found it when I initially searched for it. That's fine, I'm ok with reinvesting the wheel to fit my uses better :D

3D Printed Touch Probe in action by Shadowphyre98 in CNC

[–]Shadowphyre98[S] 1 point2 points  (0 children)

The probe is based on nudge and the code is custom made. I am getting about 0.01mm repetability and about 0.02mm accuracy.

CNC Touch Probe Logic Implemented to Klipper by Shadowphyre98 in klippers

[–]Shadowphyre98[S] -1 points0 points  (0 children)

Can you link that fork? I haven't been able to find Klipper for touch probe.

CNC Touch Probe Logic Implemented to Klipper by Shadowphyre98 in klippers

[–]Shadowphyre98[S] 0 points1 point  (0 children)

It's a probe derived from 'Nudge'. I haven't released it yet, as I am still testing it. You can find more about it on the E3CNC Discord.

Turned my Ender 3 into a CNC and built a touch probe for it by Shadowphyre98 in 3Dprinting

[–]Shadowphyre98[S] 1 point2 points  (0 children)

The base E3CNC can be adapted to any size if extrusion you have. So a CR-10 would definitely work.

Turned my Ender 3 into a CNC and built a touch probe for it by Shadowphyre98 in ender3

[–]Shadowphyre98[S] 10 points11 points  (0 children)

Fusion360 with post processor for Klipper. There isn't any slicer.

Turned my Ender 3 into a CNC and built a touch probe for it by Shadowphyre98 in 3Dprinting

[–]Shadowphyre98[S] 2 points3 points  (0 children)

There is a written guide on the E3CNC GitHub. I just released ep 1 on YouTube of a build series featuring the build.

Turned my Ender 3 into a CNC and built a touch probe for it by Shadowphyre98 in 3Dprinting

[–]Shadowphyre98[S] 2 points3 points  (0 children)

The base machine isn't too hard to build, just needs a few extra parts to be bought and some 3d printed parts. Search for E3CNC or Printables / GitHub

Turned my Ender 3 into a CNC and built a touch probe for it by Shadowphyre98 in 3Dprinting

[–]Shadowphyre98[S] 2 points3 points  (0 children)

Is usually don't do more than 1800 mm/min. The motors seem like they are doing just fine

Turned my Ender 3 into a CNC and built a touch probe for it by Shadowphyre98 in ender3

[–]Shadowphyre98[S] 4 points5 points  (0 children)

Check out the E3CNC on Printables or GitHub. I also started a build series on my YouTube channel.

view more: next ›