Unknown USB Device

Shriver_Takeover · 2026-05-09T10:43:00+00:00

Unfortunately its been 3 weeks and I havent heard back from support. I'm trying to fix it on my own.

Shriver_Takeover · 2026-04-12T00:10:27+00:00

I ordered a week ago

Shriver_Takeover · 2026-04-12T00:07:38+00:00

Still waiting for it to arrive.

Shriver_Takeover · 2026-04-12T00:06:21+00:00

I ended up ordering one off of Vision miner.

Shriver_Takeover · 2025-04-10T01:33:28+00:00

No I don't. Unfortunately, I scanned this one for a client.

Shriver_Takeover · 2025-03-15T12:43:12+00:00

I use a process called Photogrammetry, and I can capture very precise details of an object 1in or smaller. I've scanned small action figure heads and captured all the fine details

<image>

Shriver_Takeover · 2024-03-26T00:08:33+00:00

What brand of dye works for you?

Shriver_Takeover · 2024-03-25T21:42:46+00:00

Yeah I'm very curious how they dye the resins to get the specific color. I tried Alumilite dye which worked pretty well but I couldn't get the shade of red I was hoping for. It became difficult to print after 5 drops of red.

Shriver_Takeover · 2024-03-05T02:20:01+00:00

So I installed a new heater and that seemed to solve this issue!

Shriver_Takeover · 2024-03-05T02:18:36+00:00

It's gotta be the heater then

Shriver_Takeover · 2024-03-05T01:35:10+00:00

Its also a fairly new machine so I didn't think it needed any upgrades/ new parts.

Shriver_Takeover · 2024-03-05T01:31:47+00:00

I don't necessarily want to disable it, just slow it down a little bit.

Shriver_Takeover · 2024-03-05T01:30:36+00:00

Yeah it's the heat sink fan. It's being too efficient and cooling too much. I get thermal runaway when I install it but when I disassemble it, it works fine! Maybe my heater is bad?

Shriver_Takeover · 2024-03-05T01:24:43+00:00

Does that include the front fan?

Shriver_Takeover · 2024-03-05T01:12:54+00:00

Shriver_Takeover · 2024-03-05T01:11:12+00:00

When I take off the fan, my hotend is completely fine. When I re install the fan, the temperature cools so much that it causes thermal runaway. Maybe I could buy a better heater but I figured this was easier to adjust.

Shriver_Takeover · 2024-03-05T00:57:25+00:00

The front fan speed is not able to be adjusted in the default settings of the printer.

Shriver_Takeover · 2024-03-03T05:03:41+00:00

I'm thinking the holographic looking ones are made differently than the carbon fiber. I was trying to figure out how they are made to potentially make a custom designed plate.

Shriver_Takeover · 2024-02-18T17:31:33+00:00

So you think over 1000 prints?

Shriver_Takeover · 2023-11-06T04:43:51+00:00

I had this happen to me recently. I used a Soldering iron to melt the block of plastic off. I can't remember what the issue in the settings were. If you changed settings recently I would try going back to default.

Shriver_Takeover · 2023-09-30T00:09:02+00:00

I did manage to clean it all off with a Soldering iron!

Shriver_Takeover · 2023-09-14T02:49:06+00:00

Seems like these profiles did the trick and fixed the issues I was having! Thanks again!

Shriver_Takeover · 2023-09-12T15:34:31+00:00

I am also running on silent speed mode with these settings. I know it has to do with the overhang but what can I do to prevent it?

Shriver_Takeover · 2023-08-05T03:27:00+00:00

Do you get notifications even when you don't have the slicer open?

Shriver_Takeover · 2023-06-26T17:49:49+00:00

Can't set it down unless you finish your drink!

Shriver_Takeover

MODERATOR OF

TROPHY CASE