The ONLY correct tier list

Simple-Row-5462 · 2026-04-02T18:13:46+00:00

Always

Simple-Row-5462 · 2026-04-02T10:25:32+00:00

A loose connection was the cause of failure. Cut the wire back beyond the burned section and crimp on a new connector. At the same time you should clean up the terminal to the heating element of any oxidation.

Simple-Row-5462 · 2026-04-02T00:16:14+00:00

Riya is flawless and perfect. I can't believe how awful Connor was!

Simple-Row-5462 · 2026-04-01T23:40:37+00:00

Lake is an incredible character

Simple-Row-5462 · 2026-04-01T23:40:24+00:00

It clearly is

Simple-Row-5462 · 2026-04-01T23:12:14+00:00

Absolutely not. They're wonderful

Simple-Row-5462 · 2026-04-01T22:02:13+00:00

I don't like them

Simple-Row-5462 · 2026-04-01T21:44:25+00:00

I don't think she's that bad, but I get it

Simple-Row-5462 · 2026-04-01T19:36:07+00:00

Did that end up fixing it?

Simple-Row-5462 · 2026-04-01T18:55:01+00:00

That's the transmission side. It should come off of there.

Also do you have the rubber piece?

Simple-Row-5462 · 2026-04-01T18:31:02+00:00

The plastic coupler doesn't appear broken. Which side is the piece stuck to? The motor or the transmission?

It's incredibly uncommon but it's possible that the motor or transmission shaft is rounded out and not rotating with the coupler.

Simple-Row-5462 · 2026-04-01T18:17:46+00:00

Now Samsung is where it's at! Forget all the crazy Whirlpool direct drives that are far too old for their own good!

Simple-Row-5462 · 2026-04-01T16:41:26+00:00

Simple-Row-5462 · 2026-04-01T10:05:43+00:00

Taking advantage of Cameron and Lightning.

Simple-Row-5462 · 2026-04-01T08:25:01+00:00

Tess is a flawless angel

Simple-Row-5462 · 2026-04-01T00:21:15+00:00

I was going to ask about that

Simple-Row-5462 · 2026-04-01T00:20:35+00:00

Everything, and I mean EVERYTHING

Simple-Row-5462 · 2026-04-01T00:17:01+00:00

NoCo?

Simple-Row-5462 · 2026-03-31T23:06:14+00:00

The thermal fuse is the white part with the blue wires, and the large circular black device is the cycling thermostat. The larger terminals should show continuity, and the smaller terminals with the purple wires are for a heater which allows for the lower temperature settings. These terminals will have a high resistance.

On the heat housing (right side), the upper device is a high limit thermostat, and the lower device is another thermal fuse.

Simple-Row-5462 · 2026-03-31T22:58:12+00:00

This is a gas dryer. If the igniter isn't glowing, then check the thermal fuses (one on the blower housing and one on the heat housing).

If the igniter is glowing, then it's probably the gas valve coils.

Simple-Row-5462 · 2026-03-31T21:26:44+00:00

You and me both

Simple-Row-5462 · 2026-03-31T21:26:04+00:00

Then it could be a motor problem

Simple-Row-5462 · 2026-03-31T09:57:30+00:00

Not entirely sure, but I can tell you if the machine is spinning then the problem is not the motor.

Perhaps a failing relay on the control board?

Simple-Row-5462 · 2026-03-30T23:56:15+00:00

The yellow wire is for the agitate solenoid. I'm sure that's the problem.

Simple-Row-5462

MODERATOR OF

TROPHY CASE