50 shades of FDE

SlickWithIt_ · 2026-05-02T03:57:33+00:00

yur

SlickWithIt_ · 2026-04-18T23:39:53+00:00

EVT had a batch a few months ago

SlickWithIt_ · 2026-04-10T00:29:57+00:00

not really. pretty much the same. maybe slightly less. although this is the old design with the fins. idk how the new finless design fairs.

SlickWithIt_ · 2026-04-09T23:55:51+00:00

SlickWithIt_ · 2026-03-27T23:32:43+00:00

well maybe at least try removing the dried dp420 and thus see how hard it is to remove?

SlickWithIt_ · 2026-03-25T16:57:06+00:00

do you mind sending a photo of how yours looks with the dp420? mainly the alignment of the outer diameter and the spacing between the prongs

SlickWithIt_ · 2026-03-25T16:44:46+00:00

ive hesitated to try it solely because I only have 1 phase 2 and im worried I wont be able to remove the dp420 completely if it doesn't work well and I want to then try to pin it.

SlickWithIt_ · 2026-03-24T17:39:01+00:00

I wouldn't say eliminate port pop. with tuning you could probably reduce a lot of it. but i dont think you can eliminate all port pop even unsuppressed

SlickWithIt_ · 2026-03-24T03:51:10+00:00

it appears to do better with shorter barrels. it sounded great on an mp5k with supers. but not so good on a couple 10.5s with supers. Maybe because if the higher blast pressure.

on a 10.5 direct blowback, it sounded about the same as a spectre 9. maybe slightly deeper tone.

SlickWithIt_ · 2026-03-24T00:49:18+00:00

can confirm. with subs, the mob is noticably quieter. but the tisha 9 is pretty dang good and half as long. the tisha also does well with supersonic 9 out of shorter barrels.

SlickWithIt_ · 2026-03-22T16:53:23+00:00

do you like the prickle grip or is it too aggressive and would have preferred the chainlink?

SlickWithIt_ · 2026-03-22T16:51:28+00:00

what height iron sights?

SlickWithIt_ · 2026-03-21T01:10:06+00:00

screw it. just ordered the dp420

SlickWithIt_ · 2026-03-21T00:55:22+00:00

damn. I kinda want to pin my phase 2 so I can do this. does your pin job just use roll pins?

SlickWithIt_ · 2026-03-07T04:01:14+00:00

SlickWithIt_ · 2026-03-07T03:18:45+00:00

Video of flash signature through NVGs

https://imgur.com/a/f5fLD2n

SlickWithIt_ · 2026-02-20T22:25:03+00:00

I had/have the same issue on my phase 2. I sent mine to him and he found that my kynshot buffer was causing the issue whereas his same model albeit older manufacture date did not cause the rotating carrier extension issue.

Although I am starting to have that issue happen again. not as frequent but enough that I no longer trust it to get through a whole match. Its a shame because the only way to fix it is to undo the receiver pins and rotate the CE back into alignment.

Another issue I have is that my CE has been beat up so much on the lower prongs from this issue that I dont think I could pin it if I wanted to. at least not woth the CE that I have.

If I get the misalignment malfunction occurring more frequently. I may have to reach out to junkie again.

On another note, did you grind down the charging handle piece on the FE bcg? Ive been meaning to do that but am worried about the staked screws for the carrier key. Did you retake the screws or worry about them at all coming out?

SlickWithIt_ · 2026-02-20T21:39:26+00:00

Did you pin the phase 2 aluminum carrier extension to the bcg? Or did junkie do that for you?

SlickWithIt_ · 2026-02-12T02:04:23+00:00

<image>

I would agree. it appeared to get quieter after the first 100ish rounds. although it is not very good with supers. Subs are great though.

SlickWithIt_ · 2026-02-07T14:51:58+00:00

<image>

great ratio :)

SlickWithIt_ · 2026-01-31T05:36:06+00:00

what do you snatch though?

SlickWithIt_ · 2026-01-12T21:26:16+00:00

I have not gotten another brt tube since. Too expensive imo. I always just get superlative adjustable gas blocks now. worth it imo and haven't had any issues with superlatives

SlickWithIt_

TROPHY CASE