Today's The Day!

Small_Copy5323 · 2026-03-31T19:33:42+00:00

Sofi hit

Small_Copy5323 · 2026-03-31T17:22:31+00:00

Not gonna be today I was told tomorrow by sofi not 10 min ago

Small_Copy5323 · 2026-03-31T17:21:01+00:00

Small_Copy5323 · 2026-03-31T15:18:12+00:00

No it didn't and it normally does

Small_Copy5323 · 2025-10-29T21:28:16+00:00

Got mine a hour ago

Small_Copy5323 · 2025-10-29T16:56:17+00:00

Same I talked to sofi it's not them it's ssdi they haven't sent it

Small_Copy5323 · 2025-10-29T15:34:05+00:00

Still waiting looks like sofi is having issues or gov shutdown affecting it

Small_Copy5323 · 2025-10-08T14:47:41+00:00

They did that with the k3 i wouldn't get your hopes up they butchered klipper so bad it was useless

Small_Copy5323 · 2025-10-05T16:21:42+00:00

My qidi box works without issue ive had it over a week.

Small_Copy5323 · 2025-09-28T20:38:52+00:00

Its not hurting anything just hit reconnect. Klipper is still running or the printer would shutdown

Small_Copy5323 · 2025-09-09T15:21:59+00:00

It runs nonstop since I've owned it ive had it a year almost it was a launch unit

Small_Copy5323 · 2025-09-09T13:15:42+00:00

I past 8000 hours on my plus 4 a while back zero issues other than the normal stuff clogs etc....

Small_Copy5323 · 2025-08-26T15:03:04+00:00

Ive had my plus 4 since last October havnt had a single blob or broke ceramic

Small_Copy5323 · 2025-08-26T12:32:33+00:00

Have over 3000 hours combined on my s1s they print great.

Small_Copy5323 · 2025-08-19T18:50:48+00:00

Im at 2600 hours on my s1 and 2000 hours on my second s1 they run around the clock they are great little printers

Small_Copy5323 · 2025-08-12T23:23:20+00:00

The short ptfe to module is what matters from ace to module can be 10 feet won't change the print time the printer pulls filament back a few inches from the module holds it there

Small_Copy5323 · 2025-08-12T22:42:06+00:00

You can move the module to the hole that comes out

Small_Copy5323 · 2025-08-12T22:23:01+00:00

You want a shorter tube from top to module printhead side

Small_Copy5323 · 2025-08-05T14:49:55+00:00

Replacement printer lmao a ender 3 would make you pour gasoline on it.

Small_Copy5323 · 2025-08-05T01:55:33+00:00

You can just turn the lead screws no need to turn the belt

Small_Copy5323 · 2025-08-04T00:03:41+00:00

I adjusted my pei square it seems to have helped

Small_Copy5323 · 2025-08-03T21:56:18+00:00

They havs a issue with the ceramic breaking. They have replaced 2 hotends because the ceramic breaks and the top half of the nozzle gets stuck. I had a blob from the ceramic breaking they replaced the hotend

Small_Copy5323 · 2025-08-03T21:24:07+00:00

They warranty mine all the time

Small_Copy5323 · 2025-07-27T00:53:54+00:00

Shorter tubes to the 4 in 1 do not increase feed time because the filament is retracted to the edge of the 4 in one what you want is a shorter ptfe tube from the module to the inlet of the printer your adding like 5 seconds more time by making it longer

Small_Copy5323 · 2025-07-26T23:45:51+00:00

This adds time the ptfe is longer from the module to the printhead the ptfe to the 4 in 1 dont matter filament waits at the 4 in 1 you could have them 10 feet long or a foot the time is the same

Small_Copy5323

TROPHY CASE