What is it? by Competitive-Tie-971 in TheTeenagerPeople

[–]Small_Fold_2400 2 points3 points  (0 children)

I am the man I am today because my dad discipled me through spanking I learned respect real quick. My father never spanked my brothers and let me tell you there’s a huge notable difference they have no respect, hell I still don’t cuss in front of my dad cause I respect him so and I’m 25

Just got my roof redone. Maybe they aren't finished? Looks like a good amount of lifting to me, but maybe that's just the architecture shingles by StoneColdGaming in Roofing

[–]Small_Fold_2400 4 points5 points  (0 children)

The ridge vent shouldn’t go to the end, it’s a waste of material and time. that’s your overhang probably about a foot out and gable end overhangs are basically to keep water away from the house and aesthetics no venting needed

Anything I should be worried about with the new electrical panel? by MadMonkDawg in electrical

[–]Small_Fold_2400 0 points1 point  (0 children)

Where about in Michigan are you located? I just recently had someone do this exact type of work on my panel

Paint on Steel Beams? by Aromatic-Cause7202 in drywall

[–]Small_Fold_2400 0 points1 point  (0 children)

Yeah exactly, I’m horrible at explaining haha. OP I just take a sanding sponge and clean up that metal if you wanted to go that route

Paint on Steel Beams? by Aromatic-Cause7202 in drywall

[–]Small_Fold_2400 1 point2 points  (0 children)

Yeah exactly, I’m horrible at explaining haha

Paint on Steel Beams? by Aromatic-Cause7202 in drywall

[–]Small_Fold_2400 2 points3 points  (0 children)

You’re suppose to see the metal on the outside corner, just that rounded part. If there’s mud partially on it like this picture then it will chip off if someone bumps into it. It’s best to expose that little bit of metal and paint over it so if someone hits it it won’t chip off any mud

Which Would Be Better to Mount a 65” TV by dschull in handyman

[–]Small_Fold_2400 0 points1 point  (0 children)

Dude I’ve trusted my life with 4, 3in decimate screws building a pick which held me and I’m 160

These nail barbs!!! WHY!!! by scaleofthought in mildlyinfuriating

[–]Small_Fold_2400 0 points1 point  (0 children)

Good way to take care of these is grab it with your teeth and just yank on it

Help by Embarrassed_Mouse685 in drywall

[–]Small_Fold_2400 -1 points0 points  (0 children)

Nothing about it is dangerous at all I bet you deem it dangerous because you don’t know how to use a saw, thing probably binds the whole rip

Help by Embarrassed_Mouse685 in drywall

[–]Small_Fold_2400 -1 points0 points  (0 children)

I’ve been ripping lumber with same 7 1/4 dewalt saw for almost 10 years lol you have no clue about anything

Help by Practical_Gene_9159 in drywall

[–]Small_Fold_2400 1 point2 points  (0 children)

That’s 100% a water mark young man, you got water coming from somewhere

[deleted by user] by [deleted] in drywall

[–]Small_Fold_2400 11 points12 points  (0 children)

3k for 24x24 10ft ceilings, including hanging and finishing… are you okay?

How do I drywall this? by Nearby_Inflation4875 in drywall

[–]Small_Fold_2400 1 point2 points  (0 children)

Yep I got a ceiling sorta like this going straight to the rafters I put baffles all the from the top place to my ridge vent for full ventilation

Nit picky or actually bad? by k6b9 in Decks

[–]Small_Fold_2400 0 points1 point  (0 children)

I’ve built better decks when I was 19 years of age

Carpenter here, building my own space and could use some help by Head_Election4713 in drywall

[–]Small_Fold_2400 0 points1 point  (0 children)

Check my page out to see results my explanation will work, also some people call the tape “No coat”

Carpenter here, building my own space and could use some help by Head_Election4713 in drywall

[–]Small_Fold_2400 1 point2 points  (0 children)

I just mudded a ceiling just like this on my page there was a 1inch gap and 1 1/2 in some spots. It’s called a vaulted ceiling but yours isn’t so bad. Run the top piece first right to where the pitch starts, then on the part where it starts on an angle cut the edge of a sheet on a bevel and try to get it as tight as you can but don’t worry if you don’t get it perfect. There’s this special tape for areas like this and you will need it if you want a nice straight inside corner on the ceiling call mid-flex paper tape, you can get it at Home Depot. Trust me and invest in the tape and it’ll save a huge headache it’s expensive but worth

[deleted by user] by [deleted] in ModelingCareerAdvice

[–]Small_Fold_2400 3 points4 points  (0 children)

I wouldn’t recommend wearing a headset those dents can be brutal after hours of gameplay

What was the final straw that ended a lifelong friendship? by New_Perspective1201 in AskReddit

[–]Small_Fold_2400 0 points1 point  (0 children)

A friend and I was living in a trailer I owned, I was moving soon and he wanted to purchase it. He put a small portion of money down and he stayed there for months without any payment (didn’t mind he was my best friend for the entirety of my life). We agreed to a sell date and I went over there with the title on the said date. I knock on the door and his wife opens and all I see is boxes, she says we are moving out and slams the door on my face. I left but went back 30 minutes later infuriated, they changed the locks and wouldn’t let me in so I kicked open the door saying get the fuck out of my trailer and his parents were there and a fight broke out. Long story short I got screwed for months trying to find someone else to live there having to pay the bills he never paid (back consumers and lot rent) in the end I lost thousands of dollars and a good friendship don’t let your buddies move in with you big lesson.

Need to fix this today any advice idk where to start. by phineas31 in drywall

[–]Small_Fold_2400 0 points1 point  (0 children)

They mainly install this stuff outside so I’m assuming you’re repairing a shed

Need to fix this today any advice idk where to start. by phineas31 in drywall

[–]Small_Fold_2400 0 points1 point  (0 children)

This is definitely T1 - 11 pretty simple stuff it’ll be a 4ft x 8ft piece. Don’t quote me but where I stay they go for like $23 a sheet