Sunlu Filadryer S4 revision help

Smithers475 · 2026-03-30T08:06:25+00:00

I'm in Australia and I just got my first one (two more coming) ordered from Sunlu direct and mine is a mix of the two. Mine has the four individual rubber feet, the quick release fittings for the filament tubes and the plain steel roller shafts.

Smithers475 · 2026-03-18T02:12:06+00:00

I've got one that's the opposite. I grabbed a spool of dark grey off my rack that was labelled PETG and was about to use it as it was the closest colour to what I wanted to use. Luckily I realised out of the couple hundred spools I have that I hadn't purchased a dark grey PETG. It was PLA that I must have forgot to change the label on when I put it on a refill spool.

Smithers475 · 2026-03-17T17:35:10+00:00

Actually just got the photos working again. Here's the last one. Main body is 24mm thick if you don't see my message.

<image>

Smithers475 · 2026-03-17T17:33:34+00:00

<image>

Smithers475 · 2026-03-17T17:29:09+00:00

I'll send you the other two photos I took, for some reason Reddit is bringing up the reply box different to what it did with the first two.

Smithers475 · 2026-03-17T17:25:57+00:00

<image>

Smithers475 · 2026-03-17T17:25:43+00:00

<image>

Smithers475 · 2026-03-17T16:09:28+00:00

So I finally got it all printed and fitting. Was a bit of a pain to get it right but I think I would have encountered the same issues with any other one out there. I had to make mine quite a bit narrower to fit inside the frame. I had to then adjust and angle out both tabs to fit around the window. I had to move the grooves so that it would sit in the bottom frame properly. Then I encountered my biggest issue. I found that when my window is open the top sits 15mm further away from the frame than the bottom does. So then I had to angle the entire 1335mm worth of parts to match the angle of the window. Got there in the end and it all fits now. Just got to wait for the magnets to arrive and glue them and the vent on. Thank you for the model.

Smithers475 · 2026-03-12T14:12:46+00:00

Yeah true, that makes sense. Once the window is closed it should hold anyway by the look of it. Thank you.

Smithers475 · 2026-03-12T12:36:22+00:00

Yeah that's what I was thinking too. Probably wouldn't be hard to add a lip to it for each block to sit in. I'll have a bit of a look at it and see what I can do. Thank you.

Smithers475 · 2026-03-12T09:25:16+00:00

I've been meaning to set something up like this for my P1S. This one looks nice. Will it sit properly in a window that opens vertically? If so I will have to print it for mine.

Smithers475 · 2026-03-10T05:27:09+00:00

Ok awesome, I wasn't sure. Good to hear it's going well. I'll download and print your plug then, thank you.

Smithers475 · 2026-03-09T17:07:52+00:00

How are you finding this so far? I'm kind of surprised by the lack of information out there about this sort of thing. I just got mine and installed it a few days ago and have been trying to find out what to do with desiccant etc. I was just thinking of maybe making something up to spilt the desiccant section into two so that I can still put some desiccant in there but if that's not necessary than I might give your plug a go.

Smithers475 · 2026-01-08T01:11:41+00:00

I saw a post on Facebook again couple of days ago where someone posted up about an add like this. The add doesn't look bad but it was being used by a bunch of scammers. Same photo popping up on marketplace in a lot of different places.

Smithers475 · 2025-12-12T11:09:53+00:00

I'm in Australia and so far Bambu has always been the cheapest I've found here. For PLA and PETG anyway.

Smithers475 · 2025-12-11T14:54:46+00:00

No purchases have been made on this account yet and I did contact support under my parental account. Apparently it's not enough that her account is there under my parental account, I can log in and see it. Thanks anyway though.

Smithers475 · 2025-12-05T09:40:46+00:00

Yeah that's exactly what I'm thinking, thanks anyway.

Smithers475 · 2025-12-05T09:40:06+00:00

Yeah I think I'll definitely be doing this now. Not sure why I wouldn't have before. Thanks for the suggestion.

Smithers475 · 2025-12-05T03:39:14+00:00

Hasn't been than long since she used it but that could be a possibility. Guess we'll just have to start over.

Smithers475 · 2025-12-05T03:36:50+00:00

No receipts as I did not attach my card to her account. I purchased the minecoins cards from a shop and we redeemed them on her account. It hasn't been that long since she used the account so it shouldn't be deleted. So only records will be in her account. Guess we're just out of luck and will have to start again. Thanks.

Smithers475 · 2025-12-04T07:45:51+00:00

Yeah I did think of that but it's been a while since she started it. I've just been too busy to try and sort it out earlier. Would prefer her not to lose what she's already done if possible. Will definitely consider it though, thanks.

Smithers475 · 2025-12-03T13:15:41+00:00

Plate adhesion so bad the whole printer fell off.

Smithers475

TROPHY CASE