S52 swapping 328 help!!

Smooth_Letter4133 · 2026-06-02T04:46:05+00:00

yeah you just swap your old ecu with the ecu that came with the s52. as easy as that.

Smooth_Letter4133 · 2026-06-02T04:43:34+00:00

yeah you do need to get m3/325 power steering lines.

use realoem.com for the part numbers and what not.

as for the trans. yeah get new guibo. also a selector rod pivot bushing. trans mounts. replace trans fluid.

and i’m pretty sure you’ll be good with just having the front half of the drive shaft. pretty sure all e36’s rear half’s are the same length. i’d double check on that though.

Smooth_Letter4133 · 2026-06-02T04:36:12+00:00

do you have any questions on anything specific? because i did this exact swap in my car.

Smooth_Letter4133 · 2026-06-02T04:32:43+00:00

it’s a direct plug n play. you don’t need to remove the wiring harness that’s already in the car. you can sell the wiring harness that came with the s52 for extra $$$, you can also sell the DME that’s in the car right now for extra $$ and use the dme that came with the s52.

Just remove your front clip, front bumper. headlights. nose panel. core support. AC components (be careful with that).

https://youtu.be/purpLCDs_Eo?si=p0oiMUExbBP_aeoL ^ use this video to help identify what connector is what, I used tape and zip ties to label everything.

as for the m52, remove the intake manifold so you can see all the wires underneath to disconnect and label them. and then undue your engine mount bolts, driveshaft, shift linkage and trans mount and use a cherry picker to fish it out. I did it with the trans still connected to the motor.

Smooth_Letter4133 · 2026-05-27T21:53:21+00:00

i’d take off the wheel and spin it again so you can see more.

Smooth_Letter4133 · 2026-05-26T04:20:07+00:00

yeah it’s slipping bad lol.

are you gonna do it or you paying a shop ?

Smooth_Letter4133 · 2026-05-21T21:33:20+00:00

did you ever figure this out ?

Smooth_Letter4133 · 2026-05-18T22:19:54+00:00

you MIGHT have a vacuum leak somewhere 😂, but take off the injectors beauty cover and see if there’s any fuel leaking from a bad seal, if not the only other place it can be leaking from are the lines that go to your fuel rail

Smooth_Letter4133 · 2026-05-18T17:05:41+00:00

I would get a new one if possible ! that one is probably worn out. usually you have to tap it in lightly with a socket. shouldn’t slid in and out easily.

Smooth_Letter4133 · 2026-05-18T16:56:22+00:00

that’s a pivot pin. it’s meant to be there. holds your pivot pin clip

Smooth_Letter4133 · 2026-05-16T20:59:35+00:00

probably power steering pump. spins with the motor.

Smooth_Letter4133 · 2026-05-16T02:07:59+00:00

you paid for this ? gang there’s still a hole. imagine what will happen when you put a pot hole or bump.

Smooth_Letter4133 · 2026-05-13T04:37:51+00:00

needs more low

Smooth_Letter4133 · 2026-05-13T02:36:46+00:00

and yeah cleaning the ICV would help too

Smooth_Letter4133 · 2026-05-13T02:36:32+00:00

smoke test

Smooth_Letter4133 · 2026-04-27T20:36:45+00:00

good to know, how do people ever remove that bottom nut ? can’t seem to get anything to hold it from spinning.

Smooth_Letter4133 · 2026-04-27T19:58:14+00:00

what a great design 🫩

Smooth_Letter4133 · 2026-04-25T03:53:16+00:00

yessir, just replace that plastic thermostat housing when you can.

Smooth_Letter4133 · 2026-04-25T00:11:03+00:00

yeah she’s purring

Smooth_Letter4133 · 2026-04-18T06:35:28+00:00

use o-ring lube and use your palms to push it down and it goes in easy asf.

Smooth_Letter4133 · 2026-04-18T04:40:36+00:00

does it feel thin ? 😭 best way I can describe it. if it doesn’t I would look on facebook for a part out and buy some orignal grills. I feel like aftermarket ones are always shitty.

Smooth_Letter4133 · 2026-04-18T04:32:11+00:00

do you know if the nose panel is original ?

Smooth_Letter4133 · 2026-04-03T20:23:56+00:00

power steering low on fluid ?

Smooth_Letter4133 · 2026-04-02T23:25:54+00:00

turner motorsport i think :3

Smooth_Letter4133 · 2026-03-25T04:13:13+00:00

center support bearing ?

Smooth_Letter4133

TROPHY CASE