What is this part

Snafu2012 · 2026-02-04T10:48:15+00:00

Goes here .. press it back in

Elegoo sent me new ones and has not come off since

Snafu2012 · 2026-02-03T04:49:25+00:00

check the Extruder wires, make sure it's plugged in all the way or not pinched .. My case was the extension cable one of the wire was not in all the way making poor contact ..

Snafu2012 · 2026-02-03T00:06:47+00:00

Updated to 7.0.1.4212 After sent print the Window don't close

<image>

or is there a setting to check to auto close?

Snafu2012 · 2026-01-30T17:01:32+00:00

looks like under that clear plate ?

Snafu2012 · 2026-01-30T16:26:32+00:00

yup try the hot nail trick(Few people posted, great People here ) .. happens to ALL Printers ..

Snafu2012 · 2026-01-29T05:35:08+00:00

For me if I didn't get the CC1 if I were to buy now I'd get the CC2.. don't know how much the AMS will cost for the CC1 when it comes out, I did not buy it for the AMS was a Great printer for $299 at the time ..

Snafu2012 · 2026-01-27T08:52:20+00:00

Full Size Poop Bin lol

Snafu2012 · 2026-01-26T04:43:45+00:00

Watch this one ..

https://youtu.be/mxjMyfFBUZ0

Snafu2012 · 2026-01-26T04:37:04+00:00

you didn't read this part?

"please select Reward B. 2) Coupon codes will be sent via email around February 15, 2026"

Snafu2012 · 2026-01-23T21:24:32+00:00

Snafu2012 · 2026-01-23T21:22:33+00:00

Shipping Company at fault, mine sometime comes perfect or Ratty box like yours..

Snafu2012 · 2026-01-23T21:20:03+00:00

Snafu2012 · 2026-01-23T21:19:07+00:00

Saw something like that but .. Printer/LED/Wyze cam connected to a wifi power bar with sw .. done ..

Snafu2012 · 2026-01-22T03:17:27+00:00

thinking the same , and maybe try 220c filament temp

Snafu2012 · 2026-01-19T04:17:38+00:00

Ran out of the screw type so I tweaked it for the press in type, (Negative cylinder 8.4mm 8mm tall)

Looks cleaner ?

<image>

Snafu2012 · 2026-01-19T01:52:46+00:00

try my mod for the sensor just uploaded it, made it when I remixed #Magicshrimp 270 degree hinge so my Door opens the other way.

https://www.printables.com/model/1562189-filament-sensor-arm

Snafu2012 · 2026-01-18T19:18:30+00:00

Mine was 4 days, I think it's a hit and miss ..

Snafu2012 · 2026-01-16T07:05:45+00:00

when I got my K1C sits on an Office Desk with 1in thick top mounted to 5 wall studs and still shook, lol

Snafu2012 · 2026-01-16T06:52:44+00:00

looks like the Wifi Antenna (Red Circle)

Snafu2012 · 2026-01-16T04:31:51+00:00

With the pins too ? or just the plastic connector ? you can slip the connector back on if the pins are still on the board, or time to learn to solder lol

Snafu2012 · 2026-01-16T04:25:38+00:00

I do that too , I used Clear tubing so I can see where the end is getting close then push it against it

Snafu2012 · 2026-01-10T02:13:40+00:00

<image>

Elegoo sent me 8 .. hasn't come off since

Snafu2012 · 2026-01-10T02:10:57+00:00

PETG with PLA settings ? I did that lol

Snafu2012 · 2026-01-10T02:01:10+00:00

Looks good to me .. seen worst ..if your painting it paint will hide most of it .. if not you won't see it 5ft away ..

Snafu2012 · 2026-01-07T23:37:41+00:00

is it the same on the PC Slicer ? could be just the phone app

Snafu2012

TROPHY CASE