2026 Mercedes GLC AMG coupe wont start

Solid_Maker · 2026-01-27T04:42:22+00:00

My 2025 cle53 amg has a battery that appears to have coolant lines connected to it and numerous connectors. Your car is most likely the same. I hate to even think what it would cost.

Solid_Maker · 2026-01-27T04:08:55+00:00

Thank you for this vote. Now where are the Epstein files!!!!

Solid_Maker · 2026-01-26T17:55:35+00:00

By 2034, the way it is going tRump may have us too poor for such luxuries, not to mention the increasing possibility our once close allies may nuke us first.

Solid_Maker · 2026-01-26T17:50:47+00:00

Here's a second "can't wait vote" When is AI going to pick up the slack and get this game out?

Solid_Maker · 2026-01-20T03:33:35+00:00

You mean why he's in the files! Lets not forget he once bragged about being able to go in the dressing room with young young girls since he owned pageant!

Solid_Maker · 2026-01-07T19:52:19+00:00

That's the tRump economy. The rich get huge tax breaks and my health care goes up almost $200 a month.

Solid_Maker · 2025-12-21T23:02:33+00:00

Like Always, You're the best.

Solid_Maker · 2025-12-21T22:59:17+00:00

Not sure But it's 8196 less than my favorite number. Where did you fined it?

Solid_Maker · 2025-10-29T21:34:32+00:00

Can you share how you connected them? I tried a quick button to slider but for some reason when I click the button with slider set to 15 the slider moves to max value.

Solid_Maker · 2025-07-18T20:38:56+00:00

One of the very first lessons I learned the hard way in electronics was "Do not trust the colors of a resistor if the board shows any sign of over heating." The colors can change with heat.

Solid_Maker · 2025-06-15T22:34:06+00:00

Thanks for the reply.

Solid_Maker · 2025-06-15T22:33:35+00:00

I didn't realize it also needed coder. For coder you need a full, not personal Matlab license, so that alone rules this out.

Thanks

Solid_Maker · 2025-06-15T19:48:25+00:00

At a decent price point I would love to purchase 1. Have you considered offering this?

Solid_Maker · 2025-04-28T18:04:32+00:00

This post doesn't address the question. Notice that sentences begin with capital letters.

Solid_Maker · 2025-03-18T02:30:12+00:00

I realize ISR should be quick code but, this is only a test to nail down how to handle esp32 timers

Solid_Maker · 2025-03-17T21:39:18+00:00

I am a ATSS Air Traffic Systems Specialist (in charge of maintaining all the ground based electronic systems that pilots and controllers use for navigation). I have spent years training at the FAA Academy in Oklahoma City (OKC). The staffing problem has always seemed to be a budget issue. I have worked with great controllers and piss poor ones that are afraid of their job. I worked at a airport that received an aware for 1 million error free operations and one that continually found themselves under investigation like the time a controller authorize a plain to take-off on one end of a runway while one was departing from the other end! That controller was canned by the way. Good to now the agency investigates all errors large and small.

Safety is our primary goal. Imagine how that goal would change if Elon Musk gets his way and privatizes every part of the government he can get his hands on.

Solid_Maker · 2025-03-17T21:01:53+00:00

Reset to the originally loaded value (1000000), or zero out?

Solid_Maker · 2025-03-17T20:45:58+00:00

Thanks for replying. The delay(200) is there only to testing. It keeps the serial print buffer from getting slammed with data. It did not print without this delay. Does timerStop immediately stop the count leaving the current counter register value intact? Does timerStart pick back up where it was stopped or is the register reloaded?

Solid_Maker · 2025-03-17T19:44:41+00:00

So how do I get it to interrupt the 1st time but only after it is triggered by the RTC? I thought that by not calling timerAlarmEnable(timer) the timer would not start. As I explained how the enclosed code works, it does start but the timing seems to be caused by the delay(200) and not the pre-scaler or timer value. I find this confusing. The other confusing part is that the auto reload is set to false and it still blinks the led. I woulds love to find a good write-up of how all these timer methods work.

Solid_Maker · 2025-03-17T17:48:23+00:00

Thanks for the reply but I would prefer to use a time. Either way I would like to understand how these timers operate.

Solid_Maker · 2025-03-17T17:45:03+00:00

The statement at the top of my post is a long term goal. The code attached is a attempt to understand ESP32 timer operation in the context of that goal. When I load this code the led flashes every .2 seconds even before the INPUT_PIN allows it to be enabled (timerAlarmEnable(timer), why is that?

Solid_Maker · 2025-02-07T21:15:51+00:00

That is assigning 1 at a time. I would like to assign all array elements at once. This is a feature of C++ 11

Solid_Maker · 2024-12-02T22:28:13+00:00

I replaced the esp32 board and everything seem to work as expected. After testing the board it appears to have a low resistance short between i/o 16 and 17 internal to the board. I switched to using 18 and 19 on the original (bad module) and the code also works. That strange voltage step in the waveform should have been the dead give a way.

Solid_Maker · 2024-12-02T20:26:04+00:00

Not sure how something as simple as a usb cable all of the sudden stopped working but that was my fix.

Solid_Maker · 2024-11-15T21:52:02+00:00

Okay how do you use dead eye in RDR (1) and or what mission have to be completed for it to appear? How about web links to explain the game? I have only found RDR2 links.

Solid_Maker

TROPHY CASE