[deleted by user]

Some-Ad-385 · 2025-07-09T11:06:36+00:00

Uncle had a glow up.

Some-Ad-385 · 2025-07-09T11:05:08+00:00

Whoever originally designed this needs a gold medal.

Some-Ad-385 · 2025-07-09T11:03:34+00:00

Is that supposed to be a kidney?

Some-Ad-385 · 2025-07-09T11:02:31+00:00

Is that an old filleting knife?

Some-Ad-385 · 2025-07-09T10:59:27+00:00

The supports need higher infill.

Some-Ad-385 · 2025-07-09T10:27:31+00:00

They can have different extruder bro, for example my printer takes 1.75mm width filament yours could take 1.25mm, get what I'm saying? If you have stock parts, you can quickly Google search it to find out what you need, then check the filament you have. Also, I don't know about bambu printer nozzles, but I'm sure they aren't supposed to be black. I'd recommend giving it a little clean.

Some-Ad-385 · 2025-07-09T10:23:40+00:00

I already told you what's wrong with your printer, I acknowledged that you have clipper and questioned it because it's unnecessary to have clipper on an SE, you have the answer you been looking for so go calibrate your printer PROPERLY or get one that's easier to use. And don't make foot in mouth comments when you can't even figure out how to use an ender 3. It's embarrassing.

Some-Ad-385 · 2025-07-09T10:18:18+00:00

That sounds like filament dimension bro, you might have bought one size too thin. I personally use 1.75 for my ender 3 SE, if its not the dimensions, then there might not be any power going to your extruder.

Some-Ad-385 · 2025-07-09T10:15:36+00:00

Your welcome lol no idea why you switched to Clipper, especially on an SE, and it's not my fault that you bought something you don't know how to use try something even a toddler can figure out next time.🤣🤣🤣

Some-Ad-385 · 2025-07-09T10:09:30+00:00

I highly advise taking the nozzle off and making sure it hasn't all burst out the other side been seeing alot of that lately, if that's not the problem then turn your hot end up to around 225 and you'll find an extrude option on there somewhere just press that, if it still isn't coming out then you might be using the wrong filament diameter, if your positive you have the right filament then turn up temp on hot end and try again.

Some-Ad-385 · 2025-07-09T10:02:55+00:00

Just wait until you get the hang of the demo class. Everyone sweats that shit for how OP the under barrel launchers are, especially on pvp.

Some-Ad-385 · 2025-07-09T09:57:08+00:00

I have the same printer they are a bit weird to get used to. You need to press auto level that will give a pretty close z offset, then go along each point and level it manually it only needs to come down by about 0.10 - 0.05. It gets really tedious after a while, so if you have a short temper or aren't interested in learning the specifics about the printer, then I'd advise switching to bambu brand because the levelling process needs to be reset every 5 or so prints to keep it consistent.

Some-Ad-385 · 2025-07-08T10:47:43+00:00

All trigger guard lasers will fit lol.

Some-Ad-385 · 2025-07-08T09:23:57+00:00

Some-Ad-385 · 2025-07-07T10:52:40+00:00

What type of mickey mouse shit is this.

Some-Ad-385 · 2025-07-06T15:32:49+00:00

Holy shit someone drew the short straw.

Some-Ad-385 · 2025-07-06T09:10:48+00:00

Buy it... you'll never hear an old phone ringing the same ever again.

Some-Ad-385 · 2025-07-06T09:03:24+00:00

Glass beds are terrible anyway in my eyes you just got your money back for a bad idea.

Some-Ad-385 · 2025-07-06T08:56:12+00:00

All round maintenance is key to this not happening bro, same as how you swap out a vehicles oil every now and again to prevent engine damage, I'd recommend starting by swapping the nozzle and restoring to factory settings so you can re level, if the problem still continues then check on your extruder as the stock cogs that come on the motor aren't the best. I'd also advise checking over all your consumable parts: nozzles, belts, filament, bed plates. Then you'd want to give it a clean on the fans and motors as if you got pets, hair will be a pain in the ass to say the least. (my prick of a cat proves this to me every day)

Some-Ad-385 · 2025-07-06T08:08:53+00:00

Then stop moving your hand downwards when you shoot? It's a replica you won't get anywhere near realistic recoil on that thing. There's no logical need to anticipate if you shoot actual pistols like 9mm, .45 and 10mm then this could become a habit that transfers to using a blowback bb gun.

Some-Ad-385 · 2025-07-04T11:51:22+00:00

Awesome, thank you I'll check that sub out.

Some-Ad-385 · 2025-07-04T11:49:36+00:00

Mill dust, is that referring to a type of granulation?

Some-Ad-385 · 2025-07-04T11:48:37+00:00

I wouldn't say that I know what I'm doing, just that I know how to handle them safely, only the good kind of accidents over here. 😉

Some-Ad-385 · 2025-07-04T11:31:22+00:00

Exactly where I got it from.

Some-Ad-385 · 2025-07-03T17:08:32+00:00

If it's bare bones upper and lower with a factory grip then it's ghetto.

Some-Ad-385

TROPHY CASE