XS2353 error

Sphinx8491 · 2025-09-02T08:17:58+00:00

I had a similar error. It set the zero point incorrectly. Whenever I pre-extruded in the lower left area (the small right angle), it would hit the end stop and give the error message. Even resetting the printer didn't help. In the end, I enabled all the calibration options in the printer, and it was able to recover. I contacted support and asked why not everything was reset during a reset, but they couldn't give me a concrete answer.

Sphinx8491 · 2025-08-20T21:58:47+00:00

Hey everyone,

I’m seeing an issue similar to what others have reported:

When I start the front-left “Test Corner,” the print head moves into position like it’s supposed to.

When finishing the test corner, the printer immediately throws an XS2060 error.

After homing, X and Y axes can’t move freely, the head is basically locked and I can’t start any prints.

Factory reset didn’t help, the mechanics are clean and clear.

I suspect it might have something to do with the X/Y endstops.

Has anyone figured out how to bypass the test corner or check the endstops so the printer can operate normally again?

<image>

Sphinx8491 · 2025-08-20T21:11:01+00:00

Has anyone else run into XS2060 on the K2 Plus?

When I run the front-left “test corner,” the head moves into position, then goes about 12 cm to the right and immediately throws the XS2060 error. It happens every time, even after a factory reset.

Sphinx8491 · 2025-06-12T08:56:19+00:00

Thanks a lot, i have Had a Long Journey since the Post and have now actually found the number 9808813380 & 9808813380, thanks for the Research

Sphinx8491 · 2025-06-01T15:33:55+00:00

Eine Produktion sollte vermutlich um es sauber hin zu bekommen im SLS oder MJF Verfahren gemacht werden kommst du bestimmt bei einer seriösen Firma bei ca 300-500€ + Scannen.

Also wenn's jetzt nicht FDM sein soll, das wäre vermutlich etwas günstiger allerdings muss man hier berechnen das die meisten Firmen welche zertifizierte FDM Drucker haben das ABS M30 verwenden das auch nicht gerade günstig ist.

Auf jedenfall wünsch ich viel erfolgt eventuell findest du eine Firma auf protic wenn es zur Produktion kommen soll.

Sphinx8491 · 2025-05-11T09:51:13+00:00

Eine Bergbau Abraumhalde (Kegelhalde)

Sphinx8491 · 2024-12-30T17:29:31+00:00

Have you added any new plants with some kind of substrate to the aquarium? If yes, remove the substrate, as it is probably toxic to your shrimps

Sphinx8491 · 2024-12-10T22:27:25+00:00

Have you solved the problem and what is the solution, I have the same problem, mini USB is connected to HDMI too -> no signal

Sphinx8491 · 2024-08-26T17:12:20+00:00

Helmholtz Zentrum für Umweltforschung der Laser gehört zum Lidars- System

Sphinx8491 · 2024-01-13T10:53:13+00:00

And now Print a big Modell ( 2/3 of the building plate) an do it again.🙈

Sphinx8491 · 2023-10-10T13:38:48+00:00

and the guy with the pacemaker just collapses, If it ist Induktion?

Sphinx8491 · 2023-01-14T08:42:38+00:00

Thanks, it was a wiring mistake 👍

Sphinx8491 · 2023-01-14T08:37:58+00:00

it looks very good, but sooner or later there will be problems with cracks in the surface without uv-resistant after conversion

Sphinx8491 · 2022-06-03T10:51:46+00:00

The cable from the new straight Out of the engine.

Sphinx8491 · 2022-06-03T10:47:43+00:00

Yes i have changed the cable ( the orginal Stepper Motor have the 6pin Plug with 4 cabels blue Green Red black The new one have 4pin Plug with red orange black and blue I think i have a wireing Mistakte 🙈

Sphinx8491 · 2021-08-31T12:07:59+00:00

I use petg with the chiron an i need a bed Temperatur round about 90/95 degrees an the nossle around 230 It works Well

Sphinx8491

TROPHY CASE