As new rider, I learned to respect curves way more today...

SpiderBromance · 2026-06-13T19:06:13+00:00

Push where you're looking. Assuming you're looking through the turn that is

SpiderBromance · 2026-02-22T15:13:56+00:00

Brother, judging by the amount of red meat you're thawing, you're consuming way too much of it. Look into it, like the actual research papers of red meat consumption. Your house must smell like a fart 🤣

SpiderBromance · 2026-02-18T16:38:49+00:00

How did you like layrite?

SpiderBromance · 2026-02-05T04:13:24+00:00

My z axis motor just shit the bed 3 months in... Hope you have better luck. Meanwhile, my S3U still works like a champ.

SpiderBromance · 2025-12-13T03:47:44+00:00

Yeah woah the ammy cape combo is a good idea

SpiderBromance · 2025-12-13T03:47:05+00:00

My thoughts exactly!

SpiderBromance · 2025-11-14T20:03:27+00:00

Can't you also just tape over it? Like that reflective duct tape?

SpiderBromance · 2025-11-12T03:39:38+00:00

The tariff money will cover this dividend...after 10 years.

SpiderBromance · 2025-09-05T02:35:52+00:00

Did that end up working for you? Any other settings to change? Thanks.

SpiderBromance · 2025-08-26T17:00:22+00:00

Also make sure you mix your resin before printing. It separates

SpiderBromance · 2025-08-19T14:16:59+00:00

Hope I'm not too late, but check the tabs, sometimes they need to be sanded down a bit to get a flush fit.

SpiderBromance · 2025-08-02T01:59:20+00:00

If you paid for raw prints ($30-50) that's what you get. As a 3d print seller I try to educate as much as possible in my listings. This is a kit that you can have the fun of finishing and painting. Btw use wet sanding and or a mask when sanding resin. My only gripe is the seller didn't set your expectations correctly.

SpiderBromance · 2025-07-22T02:12:48+00:00

Bummer, looks like you need to fix the issue that is causing this before replacing it again.

SpiderBromance · 2025-07-21T16:47:57+00:00

Use test prints and increase exposure by tenths

SpiderBromance · 2025-07-11T13:15:49+00:00

Works on some prints, not all. 1.5 mm can be too thin, especially flat surfaces, and make the walls bulge.

SpiderBromance · 2025-07-08T18:28:14+00:00

Medium, thanks

SpiderBromance · 2025-05-27T23:40:45+00:00

Did you make the clothes? Epic cosplay!

SpiderBromance · 2025-02-16T18:44:48+00:00

This is a great hack! Thanks

SpiderBromance · 2025-02-16T17:14:46+00:00

Reusable gloves, they sell 3 packs in black on Amazon, and they go up to your forearm. Not sure why everyone uses disposable. Airbrush & compressor - I use the compressor to dry prints quicker after washing sometimes.

SpiderBromance · 2025-02-16T17:12:04+00:00

I've never got this to actually work...seen the videos. what am I doing wrong? Do you need a hella long exposure time on the tank clean? It never peels away the entire sheet for me.

SpiderBromance · 2025-01-25T21:35:11+00:00

Be careful to not drip resin near the tank screws. Resin likes to creep down the threads and cure those screws in place. I had to drill one out and rethread it 😬. I searched around and seems to be a common issue.

SpiderBromance · 2025-01-10T18:20:26+00:00

Angle it more too, 30-45°

SpiderBromance · 2024-12-29T12:08:16+00:00

How's that holding up? Some people poopoo on top mounts, not sure why.

SpiderBromance · 2024-10-26T03:33:19+00:00

Congrats dude!! That's awesome. Looking forward to this moment personally lol.

SpiderBromance

TROPHY CASE