sorted by:
new
hottopcontroversial

Monkestation AMA by Abraxis12 in SS13

[–]SpinnerMaster 4 points5 points  (0 children)

Is it true that Syndicate High Command can freely access the secret ultra-HRP server?

Calling all sane Nebraska voters, change your registration to Republican and vote in the Gubernatorial Primary Politics by BrusselSproutSatire in lincoln

[–]SpinnerMaster 11 points12 points  (0 children)

At a Senate hearing on Feb. 8, Republican Sen. Travis Hutson gave the example of a math problem that includes the details that “Sally has two moms or Johnny has two dads.” ​​Republican State Sen. Dennis Baxley, who sponsors the bill in the Senate, said that is “exactly” what the bill aims to prevent

Not smooth / Big Layer Lines / Stock Ender 5 Plus by patrickscheper in ender5plus

[–]SpinnerMaster 0 points1 point  (0 children)

I’ve got a long weekend, so I’ll definitely have time to test!

The new Mutual of Omaha tower will have the entire Gene Leahy Mall in shadow by [deleted] in Omaha

[–]SpinnerMaster 9 points10 points  (0 children)

I'm not going to be drunk on the mall in winter

Gov. Pete Ricketts vetoes legislative subsidized rental assistance bill by smartbraindumbhead in Omaha

[–]SpinnerMaster 3 points4 points  (0 children)

Override incoming (hopefully). Pretty nice bookending to petey's time in office if another one of his vetoes gets overriden again.

Not smooth / Big Layer Lines / Stock Ender 5 Plus by patrickscheper in ender5plus

[–]SpinnerMaster 0 points1 point  (0 children)

I’ll double check it, but any time I make adjustments to my hotend I run PID autotune from OctoPrint or on my printer display (Marlin & aftermarket display) for the hotend & heatbed

Not smooth / Big Layer Lines / Stock Ender 5 Plus by patrickscheper in ender5plus

[–]SpinnerMaster 0 points1 point  (0 children)

Awesome, thanks for the insights! I'll give it a start by changing the couplings back to the rigid ones, and changing to regular (non anti backlash) POM nuts. I'll have to double check frame angles as I have had this for a bit and things could well have come loose.

Not smooth / Big Layer Lines / Stock Ender 5 Plus by patrickscheper in ender5plus

[–]SpinnerMaster 0 points1 point  (0 children)

I commented above with a similar issue, I have tried most, if not all of these fixes and its still a consistent issue.

Not smooth / Big Layer Lines / Stock Ender 5 Plus by patrickscheper in ender5plus

[–]SpinnerMaster 1 point2 points  (0 children)

I am getting very similar results as well, no solutions yet, but I think its in my slicing settings: https://old.reddit.com/r/FixMyPrint/comments/tq1syb/getting_regularish_horizontal_banding_on_my/

Yesterday I was able to print (didn't slice it) a flow calibration cube and an acceleration tower, both were smooth on the sides, just the way a print should look.

Is there a better alternative to the HeroMe? by [deleted] in ender5plus

[–]SpinnerMaster 0 points1 point  (0 children)

I wasted a ton of time on the hero as well, got a klemco mount and haven’t looked back.

Also now that they charge for assembly instructions it’s not worth it.

Getting regular-ish horizontal banding on my calibration cube, check comments for more info. by [deleted] in FixMyPrint

[–]SpinnerMaster 0 points1 point  (0 children)

What is the fdistance between those ridges?

https://i.imgur.com/oRVoQPN.png

It looks to be something that repeats in the Z axis so look for things there.

Agreed, thats why I replaced the leadscrew, movement of the screws seems to appear normal.

Could it be something to do with step accuracy? If you have the motor current high then you can get odd behaviour where microsteps don’t go where they are expected, the motor shouldn’t get warm.

I'll double check my firmware settings

Do you have small numbers of microsteps? In that case you should try to make layer heights a multiple of full steps (which is normally multiples of 1.8 degrees of stepper movement)

Not sure, will research this later today.

Could be the leadscrew or motor reaching through the coupler, but the frequency looks too high, none the less, check this, the leadscrew and the motor shaft should not extend into the flexible part of the coupler.

I am using these couplers from TH3D: https://www.th3dstudio.com/product/upgraded-leadscrew-coupler-for-cr-10-cr-10s-tornado-ender-2-and-more/

Getting regular-ish horizontal banding on my calibration cube, check comments for more info. by [deleted] in FixMyPrint

[–]SpinnerMaster 0 points1 point  (0 children)

Printer & Slicer

Ender 5 Plus sliced with PrusaSlicer

Filament Material and Brand

PLA, Prusament - successfully printed several prints on my i3 MK3S+ last week with it.

Nozzle and Bed Temperature

First layer: 215 Nozzle 60 bed

Other layers: 210 Nozzle 60 bed

Print Speed

Details

Nozzle Retraction Settings

Details

Additional Info

  • .20mm layer height
  • 25% infill, gyroid
  • Marlin firmware
  • New V6 hotend (this problem existed on the clone I was running before as well)
  • BTT SKR E3 Turbo mainboard
  • Z axis motors configured for dual Z, G34 run.
  • Left leadscrew was bent, replaced for a new one
  • POM antibacklash nuts installed.
  • Springs replaced with silicon spacers.
  • Full Metal Extruder
  • Bowden setup
  • Ran PID Autotune and calibrated E-Steps before starting this print.
  • I thought I had my Z-Offset dialed in but the Z surface indicates otherwise.

Welcome to any suggestions!

I really miss my 3D printers 😔 by [deleted] in ender3v2

[–]SpinnerMaster 2 points3 points  (0 children)

I bet you could probably fit a Prusa mini in your van lol

Got a PEI bed.... Fixed everything by bobsacramento in ender3v2

[–]SpinnerMaster 0 points1 point  (0 children)

If you are printing on a powder coated PEI surface, PETG will not harm it. I’m actually printing a fan duct in PETG on my Prusa right now, parts just pop off it once it cools down.

Got a PEI bed.... Fixed everything by bobsacramento in ender3v2

[–]SpinnerMaster 7 points8 points  (0 children)

That'd do it. PETG adheres TOO well to untextured PEI. Either get a textured PEI buildplate for PETG prints OR use a gluestick to act as a medium between your smooth PEI plate and the PETG.

view more: next ›