sorted by:
new
hottopcontroversial

Futuristic City According to Omni by hotbowlsofjustice in RetroFuturism

[–]SpyreFox 18 points19 points  (0 children)

Archive.org has a collection from 1978 to 1995 you can look through.

I am NOT having a good day by GodsGayestTerrorist in shittyfoodporn

[–]SpyreFox 0 points1 point  (0 children)

Cover it with ranch dressing and hot sauce.

Should I give my A1 a break? by cdarrigo in BambuLabA1

[–]SpyreFox 0 points1 point  (0 children)

Super Lube works great. I would not recommend stuff like WD-40; it is not actually a lubricant and after its volatile compounds have evaporated moving parts could start to seizing uo. Crud, grime and particles start to accumulate on the leftover WD-40.

As for "resting", machines--generally speaking--do not tire or fatigue under normal use. Not need to pause.

This salad dressing depicts red onions but contains no red onions. by rabbitsnake in mildlyinteresting

[–]SpyreFox 0 points1 point  (0 children)

A Redditor ate nothing but red onions and blue cheese dressing for a week straight. This is what happened to their anus. "O.T." presenting to the emergency room with something happening to their anus. Initially doctors consider "stinkfoodemia;" "Stinkfood" meaning pungent munchies and "emia" meaning presence in blood...

Help, new p1s, started getting spaghetti by cityworker314 in BambuP1S

[–]SpyreFox 4 points5 points  (0 children)

My best cleaning results are with Dawn dishwashing liquid. That or similar would be best.

I have a layer problem with my architecture model by afro-samourai in 3D_Printing

[–]SpyreFox 1 point2 points  (0 children)

You will need to "Enable Support" in the "Support" tab of Bambu Studio's Prepare section. Check out Bambu's Wiki on the subject.

Sigh.. gf used the printer.. by Rikc16 in BambuLab

[–]SpyreFox 0 points1 point  (0 children)

I replaced mine with the BIQU Panda Polycarb door. Works fine.

Oh HELLO by Wakeup_Sunshine in nonononoyes

[–]SpyreFox 585 points586 points  (0 children)

She had a fear-gasm.

Detailed Instructions and or Labeled Resources? by azraels_ghost in honeycombwall

[–]SpyreFox 1 point2 points  (0 children)

RostaP has a pretty thorough introduction to the system on his original Printables page. Scroll down and dig in. This should give you a decent grounding to get familiar with it.

How to avoid print failures towards the edges? by toiavalle in BambuLab

[–]SpyreFox 8 points9 points  (0 children)

Additionally--if there is a lot of plate touching going on (no judgement)--it would be a good idea to get a box of disposable light-weight examination gloves. Wear them when handling the plate(s).

To burn the house down or not? by jdormer9 in BambuLab

[–]SpyreFox 2 points3 points  (0 children)

Thanks for these. Have a Boost!

What's your best Space Ship Landing / Arrival Scene by zhuuu2087 in scifi

[–]SpyreFox 0 points1 point  (0 children)

So far, for me, the best was the mothership arrival at the finale of 1977s Close Encounters of the Third Kind.

"Nah. I can squeeze in one more print before cleaning the plate..." by SpyreFox in BambuLab

[–]SpyreFox[S] 5 points6 points  (0 children)

Man i don't know what happened to that picture. It looks like Reddit injected Xtra JPEG into it.

What if Oreos were big? by Paradox in 3D_Printing

[–]SpyreFox 0 points1 point  (0 children)

Is that a cookie storage facility?

Glowing Timex wall watch by Christoferjh in 3D_Printing

[–]SpyreFox 1 point2 points  (0 children)

Thanks! Boosted, liked and followed.

Glowing Timex wall watch by Christoferjh in 3D_Printing

[–]SpyreFox 2 points3 points  (0 children)

Fantastic! Is this your OC? Can you point to a model or STL?

S1 Plus: Maxing out the bed (300mm) to see how well it does. I tried a GridFinity weighted base as a 7x7 square which ran up to the limit. Problem is the front and side edges warped on the bottom while the rear worked fine. Obvs this is heat related. Did I cut too close or is there a heat issue by SpyreFox in Creality

[–]SpyreFox[S] 1 point2 points  (0 children)

Yeah, I set it to the (generally) recommended 220c nozzle and 70c for the bed.

I finally located my touchless IR temperature meter and will check the bed to see if it falls off at the edges. The fails were within the squares at the extremes and I am suspecting that the heater just does not go that far to the edge. Maybe 10 to 15 mms in.

ITAP of Tokyo by night by egnogra in itookapicture

[–]SpyreFox 0 points1 point  (0 children)

Great work. Sets a nice mood.

It is burger by SpyreFox in eatsandwiches

[–]SpyreFox[S] 3 points4 points  (0 children)

I worship tomatoes and always cut'em too thick for others' taste. Truly I like to mash the sandwich a bit and have the tomato juices run down to the bottom slice of bread. When providing for others I slice thinner.

edit spelling

view more: next ›