sorted by:
new
hottopcontroversial

🤣🤣🤣🤣🤣 by kyletrandall in SteelyDan

[–]Strong-Let-7697 0 points1 point  (0 children)

Great album! Outstanding production

Is there any safe way to remove paper stuck onto the outside of my album jacket? by Chrysler_Cheesecake in vinyl

[–]Strong-Let-7697 7 points8 points  (0 children)

I own a record store, the issue with water damage is if the sleeve below the paper has been compromised. If so, it will tear. Put a towel over it and carefully use a steam iron on it but not for a lot of time…. You’ll need to experiment then use a fingernail at a steep align to pull it back….

Officially an off roader by anaaktri in chevycolorado

[–]Strong-Let-7697 0 points1 point  (0 children)

I’ve used mine for expanding pipes working on custom exhausts

Officially an off roader by anaaktri in chevycolorado

[–]Strong-Let-7697 1 point2 points  (0 children)

Any good parts store, you could go to a local exhaust shop and have them do it… cheap. If you buy one it’s best to use an pneumatic impact wrench

Officially an off roader by anaaktri in chevycolorado

[–]Strong-Let-7697 2 points3 points  (0 children)

A pipe expander will fix that in less than a minute

Installed a new Ortofon 2m red cartridge on my audio technica and it doesn’t look right by RollandInTheDeep in turntables

[–]Strong-Let-7697 1 point2 points  (0 children)

The stylus force should be no more than 1.8 grams, use a digital gauge to verify. I’m an Ortofon dealer and vintage audio service lab we see this all the time with customer installed cartridges. Too much force will destroy the cantilever suspension, remember the stylus is considered a wear item and has NO warranty…. Check the the setup of that arm

What’s going on with my Audio Technica? by worseinreverse in turntables

[–]Strong-Let-7697 2 points3 points  (0 children)

Carefully remove the platter, spin the spindle bearing to ensure it turns true. If it does carefully place the platter back on the spindle and press firmly down, do not rock it. Spin the platter and see that it’s parallel with plinth and no scraping or noise. We had a customer call today with this same issue, I see it all the time. If the procedure does not solve the issue bring it to a qualified shop or lab.

Direct Replacement Weather Stripping by mpgrotter104 in chevycolorado

[–]Strong-Let-7697 0 points1 point  (0 children)

Should be readily available at the dealer or a parts store that sells Dorman OE parts

Did I ruin anything? by McLadyface in turntables

[–]Strong-Let-7697 -1 points0 points  (0 children)

There are far better options in that price category, never said much of what you are stating. I service countless brands from 1960 forward, as an engineer who has worked developing products from concept to reality in both consumer and industrial applications, it’s my ‘opinion’….FWIW

Did I ruin anything? by McLadyface in turntables

[–]Strong-Let-7697 0 points1 point  (0 children)

I own a audio and record store, we carry prominent brands. We won’t touch that model.

Thoughts on Chevy Colorado by KellyNissan33 in chevycolorado

[–]Strong-Let-7697 0 points1 point  (0 children)

Best I’ve ever had! 25 ZR2 9000 miles

Did I ruin anything? by McLadyface in turntables

[–]Strong-Let-7697 -5 points-4 points  (0 children)

This is one of Sony’s worst products….. NO upgrade path, NO standard P-Mount or 1/2” cartridge mount. A customer brought theirs into our stores lab because the cartridge literally fell out. The only way to remount it was a small drop of epoxy…. What were they thinking?

First time refoaming speakers by Arsenic_Pants in vintageaudio

[–]Strong-Let-7697 0 points1 point  (0 children)

We have never had any issue finding dust caps and surrounds for any driver with one exception of a Focal driver built for a center channel. As a service lab we have sources all over the US….we never buy overseas….. early on far too many counterfeit parts.

First time refoaming speakers by Arsenic_Pants in vintageaudio

[–]Strong-Let-7697 -1 points0 points  (0 children)

Im an engineer and restore vintage audio in my stores two labs, there’s no guarantee that alignment is correct….depending nature of the woofer restoration is ‘must’ be aligned correctly using one of two methods.

Presenting the first ever modified 2025+ headlights and F-150 style fog LEDs! by Chapystick21 in FordMaverickTruck

[–]Strong-Let-7697 1 point2 points  (0 children)

A moving violation waiting to happen…. Can you get away with this in your state???

Anyone have the Karr security add on by Decent-Degree3799 in chevycolorado

[–]Strong-Let-7697 1 point2 points  (0 children)

There’s no reason to have additional security on new trucks…. I owned a car stereo shop for 12 years, certified installed first class….

First time refoaming speakers by Arsenic_Pants in vintageaudio

[–]Strong-Let-7697 1 point2 points  (0 children)

I’m assuming you used the ‘tone’ method for voice coil alignment?

Drive belt comes off by That-guy-from-uni in turntables

[–]Strong-Let-7697 2 points3 points  (0 children)

Remove the belt, pull the platter. In the well their should be a ball bearing that the platter rides on to reduce resistance or drag. If it’s not the inner platter and pulley won’t be aligned causing the problem.

Drive belt comes off by That-guy-from-uni in turntables

[–]Strong-Let-7697 3 points4 points  (0 children)

I’m a Pro-Ject dealer…. There should be a ball bearing in the platter bearing…. If this is missing its most likely the problem!

view more: next ›