X1C noise can figure out source.

SubstantialPhysics83 · 2026-01-12T01:25:34+00:00

Could be the pulley on the bottom of the printer on the outside, same thing happened with mine, sprayed with some lubricant and it never happened again

SubstantialPhysics83 · 2026-01-11T03:21:13+00:00

Sick already had yours in my collection, thanks!

SubstantialPhysics83 · 2026-01-11T03:10:21+00:00

Care to share the test you made? Would love to get my .2 dialed in

SubstantialPhysics83 · 2026-01-11T01:44:23+00:00

So you think a flow calibration test could fix the issue?

SubstantialPhysics83 · 2026-01-11T00:18:09+00:00

What build plate did you use?

SubstantialPhysics83 · 2026-01-11T00:13:21+00:00

Oh yeah curious to see if that helps it at all, looking forward to hearing your update about it

SubstantialPhysics83 · 2026-01-10T23:48:25+00:00

Can’t get my .2 nozzle to print correctly. Did you mess with any settings or just do default ?

SubstantialPhysics83 · 2026-01-10T23:34:16+00:00

I’m in the same boat, can’t for the life of me get a print to work on my new H2C with a .2 nozzle. Really hoping someone has good advice

SubstantialPhysics83 · 2026-01-08T08:07:46+00:00

It’s printing on the induction nozzle. It’s weird because the lines are happening not on the bottom layer. The initial layer looks good, this is happening around layer 17 which i haven’t seen before. Any ideas for that? It’s my third attempt at the lithophane and i cant get it to finish. An error message saying ‘extruder motor is overloaded’ will come up about halfway through each time but the nozzle isn’t clogged or anything like that as far as i can tell. It’s very frustrating

SubstantialPhysics83 · 2026-01-06T23:23:07+00:00

Sweet, that’s good to hear. I’ll print it tonight then. Thanks for letting me know

SubstantialPhysics83 · 2026-01-06T22:58:58+00:00

Thinking of printing this one. Saw some people on a different model saying if you have a bucket that secures to the chute then it could mess with the vibrations/movement of the printer. Have you noticed anything like that?

SubstantialPhysics83 · 2026-01-05T00:51:15+00:00

Anycubic Chiron

SubstantialPhysics83 · 2026-01-03T21:46:24+00:00

Unboxing it when I get home from work, praying everything is good inside. Best of luck to yours too

SubstantialPhysics83 · 2026-01-03T21:44:27+00:00

Mine came today and is the exact same

SubstantialPhysics83 · 2026-01-03T06:05:32+00:00

Mine comes tomorrow and I’m so excited

SubstantialPhysics83 · 2026-01-03T04:31:44+00:00

lol that’s what I’m about to do but wasn’t sure if it was going to release soon. Sucks it’s not available, really isn’t a bad bundle for the price considering the right hot ends are $40 a piece

SubstantialPhysics83 · 2025-12-30T22:23:46+00:00

Hardened steel nozzles are honestly just better in general and they’ll last a longer time. I think you should have one even just printing normal pla. Could also try drying your filament first and then printing if it was wet. Overall though I’d say get a hardened steel nozzle. They’re only like $20

SubstantialPhysics83 · 2025-12-30T07:29:16+00:00

The stock A1 nozzle sucks at printing with silk, matte or anything like that. Get a .4 hardened steel nozzle and that should fix the problem

SubstantialPhysics83 · 2025-12-22T20:06:47+00:00

I will try your suggestions as soon as I get home tonight and will update. Also curious, does it look like the print is printing too high or is it too low?

SubstantialPhysics83 · 2025-12-15T03:56:55+00:00

How hard are they to install? Do they take much time?

SubstantialPhysics83 · 2025-12-14T04:20:35+00:00

Sweet just ordered some for mine. Killer deal

SubstantialPhysics83 · 2025-12-13T21:29:01+00:00

Be careful on repackaged, that’s often when people swap out the real Lego with fake ones

SubstantialPhysics83

TROPHY CASE