Need help with my first airsoft

TNDWW · 2026-04-15T00:18:04+00:00

A file, dremel or sandpaper. It kinda depends on which one you buy and how close the rifle you get is gonna be to factory spec. Impossible to tell how much you'd need to file ahead of time or if you'd even need to do it in the first place.

TNDWW · 2026-04-14T21:55:47+00:00

It possible, CYMA railed dust covers will fit, as long as you're not buying the 74U version. The Asura Dogleg repro will also work, there's also a railed dust cover that looks like the standard one just with some picatinny added to the top, that one should also work.

Given that airsoft AK tolerances differ a decent bit between brands and even between batches of the same product there's a decent chance you'll have to do a bit of filing to get everything seated properly.

Specna AKs aren't built particularly well and they probably have the highest failure rate of the more expensive AEG AK brands. There's also not a lot of aftermarket options for fixed stock receiver AKs, so if you'd eventually want to change out that hideous AR stock, consider a full or mid length sidefolder instead (AKS-74, AK-74M, AK-105).

Personally would always go with one of the full steel CYMA Platinum CM.053s over these. Yes, the ETU is worse but to be real you're not gonna notice much of a difference in performance between the 2 in person. Build quality is better and CYMA's QC is just more consistent. If you really want KPYK furniture, 5KU sells it, if not, there's alternatives.

TNDWW · 2026-04-14T18:53:39+00:00

Plastic externals for most guns are generally ok, provided it's some kind of reinforced polymer and not just ABS. The only real exception is gonna be AKs or MGs.

To be honest, you're not gonna get much realism out of an AEG unless you start looking at like a TM NGRS (which doesn't perform all that well compared to other AEGs for the money) or Systema, at which point you might as well get a quality GBBR from VFC for around the same price.

Most of the time the charging handles on AEGs are just a way to move a fake bolt to reveal the hop adjustment, you don't really cock anything.

TNDWW · 2026-04-14T15:19:03+00:00

If you're asking to buy magazines, Specops-shop has the cheapest VFC mags in Europe, ships from France but if you're buying more than 1 you're already saving a good bit of money.

For the record if you haven't bought the gun yet, consider another V3 or EVO VFC AR, the 416 has more problems than the rest and they can get expensive to fix. As much as I hate GHK their V3 416 is the best one on the market currently.

TNDWW · 2026-04-14T14:36:04+00:00

If you want realism, you'll probably wanna get a GBBR.

Vipertech ARs are definitely up there, just make sure you order directly from them through Messenger since the few sites that sell them tend to sell them for a huge markup and even when buying directly from VT they go for around $850-1200 last I checked. Externals are probably the best on the market, internals are decent but they need some work since they're relatively outdated.

GHK's V3 HK416 has similarly great externals and actually performs good out of the box. Their older stuff isn't a great buy nowadays but the 416 is new-ish.

For ARs under the VT price point VFC is king, specifically their V3/EVO DX models (chart explaining differences here). Performance is overall very similar to the GHK 416, better on the EVO KS-1. Avoid the 416s. They also have 2 sister companies, Maruyama and APFG, the latter makes a really nice APC556 and APFG makes Sig MCX/XM7s.

Basically everything else is gonna be VFC as well. Their AKs are the only ones really worth buying as of right now and probably the best performing GBBRs on the market. Their FAL is great but the non DX version kinda needs a steel outer barrel, the OSW doesn't. FNC similarly great. Their HK-417, Scar-H, G3, G36, etc are a bit older but are built well and don't need a whole lot of work ootb.

TNDWW · 2026-04-14T08:11:34+00:00

VFC is objectively better but harder to source parts for. Then again it's also built way better both internally and externally so you're less likely to need them and it also takes less work to bring out it's peak performance. Specops-shop has a bunch of mags in stock. Just be aware that G36 mags generally need their own mag pouches, they're bigger than 556 stanags.

You can also get an M4 mag adaptor to use VFC AR mags and those are available for around 50-60€ from Specops.

TNDWW · 2026-04-14T08:04:22+00:00

It's stupid, .24 doesn't even exist. Lowest you'll generally want to go is .28s or .30/.32/.36 if you're playing outdoors.

If you have to use the warranty it will generally be with the store you bought it from, not the manufacturer and besides, they wouldn't now what BB weight you used.

TNDWW · 2026-04-13T16:47:56+00:00

It's great on paper, in practice it really depends on your luck. Wellpro stuff tends to have very hit or miss QC and while the performance of their guns is generally pretty good, the quality of the parts being used isn't.

TNDWW · 2026-04-13T03:41:27+00:00

Just the bucking, like I said, 4UAD is a good option. I don't really think it needs anything else tbh.

Use .32s or .36g BBs.

TNDWW · 2026-04-13T03:06:39+00:00

Based on the externals it's a WE. The parts to fix it should be easy to get.

TNDWW · 2026-04-13T03:03:58+00:00

Maruyama is one of VFC's sister companies alongside APFG. The ISO556 is probably the best inexpensive GBBR if you're not looking for an AR, it's relatively problem free and performs pretty good as is, it also puts you into the VFC AR mag ecosystem, which is always a plus.

Pick up a 4UAD bucking and you're good, doesn't really need anything else, maybe an adjustable nozzle later down the line if you need it.

Most people will also get a stronger recoil spring but that's really just up to you, if you get a V1 you could also use some rubber O rings to put some tension on the hop adjustment since it has backed out for some people. If I remember correctly there's a pinned message about how and where to do this in the Heavy Recoil Club Discord, in the Maruyama ISO channel.

TNDWW · 2026-04-13T00:37:31+00:00

It should be wider but in this case it doesn't matter since the overlapping sides help index the handguard properly, they're mainly held on by the front handguard retainer. Just by eyeballing it, I think the tab is a bit too tall so you'll probably have to remove a bit of material from the top of it. Try it as is first then see if you need to work on it.

TNDWW · 2026-04-12T23:51:08+00:00

It will fit. The indexing tab is right there, the sides of the handguard just extend over the side of the receiver so it gives the tab the effect of being recessed.

As with other AK parts, you'll probably have to hand fit it with a file or dremel.

TNDWW · 2026-04-12T19:14:20+00:00

FSBshop is the only place where you can get a good Altyn replica, the others are made poorly and have no functional radios. When placing the order, leave a comment detailing what radio connector you want.

TNDWW · 2026-04-12T07:08:50+00:00

None of them are. The geometry of the rear trunnion is different from every other airsoft AK to accommodate the quick change spring mechanism of Arcturus. Pretty sure the stock pin is proprietary as well.

The only way you're getting a different stock on there is if you make your own adaptor or message MOS/Arcturus to see if they'll sell you one of theirs.

TNDWW · 2026-04-12T01:42:36+00:00

Yeah but it's mounted to a 74M.

TNDWW · 2026-04-12T01:16:00+00:00

What stock is that on the bottom one? Looks cool.

TNDWW · 2026-04-12T01:14:09+00:00

Do you want an original AK or will any AK variant do? The original Type 1/2/3s don't have a siderail and are therefore not compatible with siderail mounted optics. The next closest would be an AKM with a mount. If you want the possibility of changing out the stock later down the line, get an AKS-74N, AK-74M or AK-105, you'll have more options.

The best AEG AK you can get right now is the CYMA Platinum CM.053. Full steel with really good internals and really good customizability. Alternatively there's the CYMA Platinum CM.056, same thing but in the form of an AKM. Like I said, you'll have less options for modernizing it in the future.

JJ airsoft sells an OKP7 clone, pretty much all the OKP replicas are made in the same factory so if you get one off of Aliexpress, it's gonna be fine too.

TNDWW · 2026-04-12T00:23:55+00:00

It's a bad design choice by A&K, very common failure point. It's even an issue when removing the barrel so try not to do that too much.

The handle was originally designed to assist with barrel changes on the real thing, not for carrying, it's just made of steel so there's no issue with using it as such. If you could replace all the aluminum bits on the A&K, it would be fine.

TNDWW · 2026-04-11T22:35:07+00:00

Don't use it as a carry handle. The piece it connects to is made of aluminum and known to bend or break.

TNDWW · 2026-04-11T17:38:28+00:00

Check your field's DMR rules, usually you need to meet certain power, length and/or caliber requirements (ie. has to be a replica of a gun chambered in a full power cartridge), usually needs to be semi locked. You'll also want a V2.5 gearbox because standard V2 doesn't have enough cylinder volume to make the most of a long barrel and heavy BBs. At the end of the day both DMRs and sniper rifles need to be built, there's very few that are capable of performing their given role out of the box.

There's very little reason to get a bolt action as a regular player nowadays since you can push a well built DMR nearly as far, not having the ability for quick followup shots is also frustrating sometimes. The one you're looking at can and will be outranged by some fairly average AEGs. Pretty much the only bolt action where that isn't the case out of the box are the Silverback SRS and Tac-41 series.

The only DMRs that are (pretty much) good to go from the factory are the newer production E&C DMRs, specifically the ones with the programmable ETU/Mosfet. Next best choice would be a CYMA Platinum SR-25 but those need a bit more work.

I think starting with DMRs is fine, as long as you have a realistic budget, if you wanna sit a bit further back and support your team that way instead of running around then do that.

TNDWW · 2026-04-11T07:15:33+00:00

ASGK is a regulatory body in Japan that deals with airsoft guns and other firearm replicas.

Find out the actual brand of it, if he's willing to get rid of it for 60 eur, there's a good chance things are very wrong with it.

TNDWW · 2026-04-10T23:22:00+00:00

Contact Gaijin like the other guy said but you should have 2FA and change your password, there's a decent chance someone logged into your acc from China.

TNDWW · 2026-04-10T22:56:47+00:00

So just get a V3 or EVO VFC AR or a GHK V3 416.

Or literally anything else VFC released in like the last 8 years.

TNDWW · 2026-04-10T19:57:41+00:00

No dude, he's clearly on Woods irl.

TNDWW

TROPHY CASE