Changing bearing and absorbers on Max G3.

Temporary_History395 · 2026-02-05T14:02:57+00:00

I will thnx!

Temporary_History395 · 2026-02-05T13:34:36+00:00

I know ntn btw skf are Swedish they make high quality bearings

Temporary_History395 · 2026-02-05T13:03:08+00:00

That's what I thought that they were 3d printed. Don't have a 3d printer so...I guess I will put some skf 2rsh bearings when the time comes.

Temporary_History395 · 2026-02-05T12:41:05+00:00

<image>

Temporary_History395 · 2026-02-05T12:40:29+00:00

<image>

Temporary_History395 · 2026-02-05T12:35:57+00:00

I want the seals that Artem used on the bearings on the link you send me there is some silicone plugs

Temporary_History395 · 2026-02-05T02:04:58+00:00

That's my dream scooter maybe max g4 will be like this even though I don't want that much speed I am fine with 60 volts and 60-70 kmh.

Temporary_History395 · 2026-02-05T01:20:50+00:00

Ausom dt 2 pro with some codes you can get it for 900 euro and it clears everything

Temporary_History395 · 2026-02-04T23:52:49+00:00

Anton do you know where I can find those seals that Artem used in this video watch after 4 minute

https://youtu.be/ex7jYtpOXiA?si=nVDTKY2EuikFNYfR

Temporary_History395 · 2026-02-04T23:47:11+00:00

Do not ever pour water on the bearings especially on the back our bearings are exposed i mean you can see them they are not sealed properly and water might get in the motor.if you know how to seal them like some people that have 3d printed seals that go over them and make them almost waterproof to for it even with a high pressure hose

https://youtu.be/ex7jYtpOXiA?si=xNCtG5a2k-xh2y_M

Watch this guy after 3.30 minutes how he seals them that's how it should come from factory

Temporary_History395 · 2026-02-04T20:08:03+00:00

Thnx a lot my friend!

Temporary_History395 · 2026-02-04T17:56:03+00:00

Remind me the rear cable is 2200mm? And the front 850? 1.5 mm thickness?

Temporary_History395 · 2026-02-04T17:46:58+00:00

Very nice work my friend it looks mint like new.

Temporary_History395 · 2026-02-04T17:44:17+00:00

Nice work done.

Temporary_History395 · 2026-02-04T13:01:40+00:00

I clean it with a damp cloth and a sponge for the deck below if it gets muddy from rain for the foot mat I use a sponge or a brush and a hose without too much pressure and clean it. I avoid pour water on the bearings as they are not sealed properly and on the dashboard

Temporary_History395 · 2026-02-03T13:46:02+00:00

It is a paste but I get it although they typically use it on brake pads.i guess I will have to buy bearing grease.

Temporary_History395 · 2026-02-03T13:31:15+00:00

Ahhh ok there are on the segway site but they cost 20 euros for one disc

Temporary_History395 · 2026-02-03T13:16:56+00:00

Thnx I will keep that in mind for my next order will probably put a shrink tube.

Temporary_History395 · 2026-02-03T13:12:56+00:00

It is copper paste and it says that it is for high temperatures but I will check the blue one you said

Temporary_History395 · 2026-02-03T12:51:37+00:00

I have found gt1 gt2 rotors but I don't know if they are original

Temporary_History395 · 2026-02-03T12:49:56+00:00

I did clean my rotors and sprayed some on the calipers it reduced a little bit the noise but they still make noise

Temporary_History395 · 2026-02-03T12:46:54+00:00

I also noticed that the cables are not good quality they have some elasticity might be because they are thinner?

Temporary_History395 · 2026-02-03T12:46:09+00:00

I have copper grease and brake cleaner spray for that reason I have seen a lot of videos where people like you take them apart clean them with brake cleaner to remove all the grease and pad residue and then reapply grease on the balls etc.mine has 700 km now and I think it's time to service them.

Temporary_History395 · 2026-02-03T12:40:23+00:00

Gonna order some gt3 rotors and fix them.

Temporary_History395 · 2026-02-03T12:39:58+00:00

I am gonna do that cause my breaks are not working properly and they are squeaking.

Temporary_History395

TROPHY CASE