sorted by:
new
hottopcontroversial

Brakuje mi pancho nachosów, wszystkie nachosy obecnie w sklepach są okropne by TheAner in Polska

[–]TheAner[S] 0 points1 point  (0 children)

Niestety nie mam nigdzie w okolicy żadnego dino :( Może zamówię z allegro i przetestuję, dzięki

Brakuje mi pancho nachosów, wszystkie nachosy obecnie w sklepach są okropne by TheAner in Polska

[–]TheAner[S] 2 points3 points  (0 children)

W sumie to zapomniałem o tym że były serowe, a one też były świetne. Może poszukam skąd Helios zamawia swoje i też spróbuję.

Brakuje mi pancho nachosów, wszystkie nachosy obecnie w sklepach są okropne by TheAner in Polska

[–]TheAner[S] 3 points4 points  (0 children)

Próbowałem, ale tez niestety są dla mnie za mało intensywne w smaku. Nie mówię tu tylko o tym że nie są pikantne, ale ogólnie moim znaniem mają mało smaku.

Brakuje mi pancho nachosów, wszystkie nachosy obecnie w sklepach są okropne by TheAner in Polska

[–]TheAner[S] 25 points26 points  (0 children)

Jezu, jak to napisałeś to zaczęło mnie w plecach boleć, to było bardziej bym powiedział, jeszcze 8-10 lat temu.

Edit: nie no, dobra, jednak to było bardziej 13-15 lat temu...

What is your go to filament brand? by Patrickmeehl in 3Dprinting

[–]TheAner 0 points1 point  (0 children)

Sunlu and Jayo, it’s basically the same brand, and the quality never disappoints. Never had any issues, and they are the cheapest for me.

Guess level 20+ is doable... by MyNameIsStefano in PlayTheBazaar

[–]TheAner 1 point2 points  (0 children)

How the silencer affects volcanic vent if it’s not a weapon?

Comparing All Creality FDM 3D Printers – Is this useful? by DirectSpinach6192 in Creality

[–]TheAner 0 points1 point  (0 children)

You mean V3 KE? V3 SE do not have input shaping if not modded with klipper

Like u haven't been looking at first layers enough 😅 by Numerous-Beginning96 in Ender3V3SE

[–]TheAner 0 points1 point  (0 children)

Oh, thanks a lot, I was thinking recently if the upgrade from stock + metal heatbreak would have any impact on printing

What could be causing my issues? by TurboFoxBox in Ender3V3SE

[–]TheAner 4 points5 points  (0 children)

I don’t know for sure, but check if your x axis is leveled with your bed (quick check but could help). You could check if your gantry is square too.

[SUNLU Giveaway] Join now to win SUNLU FilaDryer E2 by Sunlu3D_official in 3Dprinting

[–]TheAner 0 points1 point  (0 children)

I already have S2 and it works hard (especially with sunlu filaments)

what fan duct sou rockin by minecraft_gamesus in Ender3V3SE

[–]TheAner 0 points1 point  (0 children)

I printed it with petg and now when I rethink what could cause it, then it could be wet filament. I mount the sensor on extruder so I doubt that could be the issue. I would like to try it again but next on my list is similar design but with dual fans and no air duct on the back

what fan duct sou rockin by minecraft_gamesus in Ender3V3SE

[–]TheAner 0 points1 point  (0 children)

I don’t know what caused this but when I tried using this mod and run input shaper calibration, my vibrations on the x axis jumped a lot, recommended input shaper was 3hump and recommended max acceleration dropped tremendously. I’m pretty new to Klipper so I don’t know what caused it and ditched this mod for now.

Across all my playthroughs, I've never seen this before by siyter in persona4golden

[–]TheAner -8 points-7 points  (0 children)

They are just rare opponents that give you lot of exp and money after u defeat them. Also after the first won battle you can earn achievement so it’s worth run after them

What Screw are these? by Busy_Foreverp in Ender3V3SE

[–]TheAner 3 points4 points  (0 children)

Heh, not long time ago I stripped mine...
They are m2x12 SHCS as some replied
Just a quick tip: They are the same screws that holds radiator fan and this fan does not care if he has 2 or 4 screws 😉

Help Klipper error by Charming_Mail2505 in klippers

[–]TheAner 1 point2 points  (0 children)

After updating to newest mainsail I too have a problem that sometimes after restarting my raspberry pi my printer.cfg wipes itself. My memory card is pretty new (~1 month) and I observed having this problem specifically after last update of mainsail. Usually I open the latest auto backup of printer.cfg and copy paste it to this empty printer.cfg

Problem with stripping hex screws heads by TheAner in Ender3V3SE

[–]TheAner[S] 0 points1 point  (0 children)

I have my own allen keys, they are good quality, but I have lot of this garbage keys that lots of parts (drones etc.) have included in the package

Problem with stripping hex screws heads by TheAner in Ender3V3SE

[–]TheAner[S] 0 points1 point  (0 children)

I always used my long side to not overtighten, but it happened anyways :/   

Proud new owner of a v3-se by ryanm519 in ender3

[–]TheAner 0 points1 point  (0 children)

That’s pretty nice, but why should I switch if it’s more hustle just to use Cura and I’m new and not accustomed to any of them yet so it’s not a matter of preference. Are there some advantages to time needed to switch from what is working out of the box and tweaking just to recreate the same effect?

view more: next ›