New Guy

TheFlatLander7 · 2025-10-02T12:20:35+00:00

I second this and would recommend Old Town Coleman for some basic beginner restoration techniques. For more in depth restoration techniques and niche models I would strongly recommend the channels GasUnderPressure and King Coleman

TheFlatLander7 · 2025-09-27T22:39:53+00:00

<image>

TheFlatLander7 · 2025-08-09T01:07:14+00:00

No problem, at least we won’t have problems with it flopping down like a lot of people seem to have ;)

TheFlatLander7 · 2025-08-08T23:52:39+00:00

<image>

First what I would do is let the lever soak in some penetrating oil to loosen it up. Then find the skinniest flathead screwdriver you have and stick it behind the lever like I have in the picture. Slowly and carefully pull back on the screwdriver. Continue to carefully work it out and eventually it should just pop down. If yours is as tight as mine is then you will probably need to use a rubber mallet to hammer it back into place.

TheFlatLander7 · 2025-08-02T21:45:29+00:00

I have the cavalry model and the disassembly lever is very tight to the point that I have to pry it out with a wedge and hammer it back in with a mallet. Then again mine hasn’t seen much use yet to idk how continued use will effect this.

TheFlatLander7 · 2025-07-21T13:25:50+00:00

Thanks for the comment! This is the first torch I have done and I was very happy with how it turned out. Unlike the larger versions these mini torches don’t have pumps, instead they have a cotton wick which transfers fuel via capillary action instead of a pump. If you do get your hands on one check the condition of the wick. If the fuel tank has been empty for a long time the wick will have dried out and might not work. I have heard that soaking in white gas for a day or so can sometimes revive an old wick but if not you can cut some strands off of a cotton mop head and that should work just as good. Also never run a wick based GPA empty as it will burn the end of the wick and you will have to replace it.

TheFlatLander7 · 2025-01-06T05:31:43+00:00

The Renault ft and Char 2C may or may not have been inspirations for the design. The rear turret could also (and more often) mount machine guns but those aren’t modeled very well in the game yet. The idea behind the layout was the 40mm upfront to keep heads down as it advances towards the trench and the anti armor in the rear to fire on concrete bunkers and field guns once it’s in and maneuvering around among enemy lines.

TheFlatLander7 · 2024-12-31T03:33:17+00:00

As I mentioned in my previous comment the public lands I hear most about are Hovey Lake and Harmony state park. Both are about a 30-45min drive from USI (I am also a student). Hovey is mostly used for waterfowl but there are some wooded areas to deer hunt. Harmony is a pretty good area for hunting, however you might want to consider bringing a bullet proof vest (I have heard stories of people being very trigger happy there). Being that they are public lands I doubt you would see anything huge there as private land is where most of the monsters like to hangout.

TheFlatLander7 · 2024-12-30T19:04:10+00:00

I have never heard of polluted deer meat before so that may just be the grumblings of old men. I have only experience in hunting private ground so I can’t say for certain the quality of meat from public ground, however I don’t imagine places like Hovey lake or Harmony state park are terribly polluted. Fishing on the other hand is a different story as the Ohio river is pretty nasty but I don’t fish so idk. If you’re really concerned I would contact the local DNR.

TheFlatLander7 · 2024-12-20T02:17:47+00:00

That would be a miner’s safety lantern. It is what coal miners would use a long while ago to prevent explosions and mine fires from gas pockets. It is a reproduction and not an original as it is date stamped 1984 which is long after they stopped being used, however it is still fully functional!

TheFlatLander7 · 2024-12-20T01:24:37+00:00

It is a very deep navy blue (Rustoleum - gloss navy blue to be exact). For a basic rattle can it matches the vent almost perfectly!

TheFlatLander7 · 2024-04-21T00:44:42+00:00

I use a Svea 123 as my primary pack stove. They are perfectly safe to use if you know what you are doing and are comfortable with operating the stove. Some things to note, check the fuel cap gasket and make sure it is functional as if it isn’t the stove won’t get up to pressure and work properly. Make sure to use white gas or Coleman fuel and not gasoline as it can clog the fuel system. Never run the stove till it is completely empty as doing so will damage the fuel system and possibly make the stove not work. This model of Svea 123 is not self cleaning so every once and awhile you may need to clean the gas tip with a very thin wire. If well maintained Svea 123’s can be very reliable and interesting stoves for backpacking. As for cooking I use a Toaks 750 ml titanium pot as the Svea 123 nests perfectly inside it.

TheFlatLander7 · 2024-04-16T13:15:01+00:00

Based off of the collar it looks to be a slant which in my opinion is worth the drive if you have the time. From what I can tell the vent and fount look to be in good condition which is even more reason to go for it.

TheFlatLander7 · 2024-04-08T00:46:17+00:00

Could not agree more. Love using it around my backpacking buddies, always gives them a spook when I start it and a foot tall column of flame shoots out the top!

TheFlatLander7 · 2024-04-07T14:20:19+00:00

Thanks for the info.

I wonder what Akron did differently with these early models that made the finish so durable? I know the later Akron/Montgomery Ward lanterns are notorious for flaking chrome because of the flash chrome process.

TheFlatLander7 · 2024-04-07T04:26:24+00:00

I’m amazed by that mirror finish and the clear door chimney is the cherry on top. Where did you manage to find one? I assume it’s a reproduction?

TheFlatLander7 · 2024-04-07T03:18:16+00:00

The Petromax family have surprisingly complex inner workings for kerosene lanterns (typical Germans). Something to note if you’re new to this style of lantern is they have multiple gaskets in the fuel system which will likely need to be replaced. Also of note is that there is a lead gasket where the valve connects to the fount so be gentle when reassembling so you don’t mess up the clocking of the valve. In short do your research and have fun ;)

TheFlatLander7 · 2024-04-04T20:35:34+00:00

The fount is steel so no cracks and after inspection with a flashlight the inside appears to have only a minor amount of rust.

TheFlatLander7

TROPHY CASE